Wood-mizer MK20-2 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 86

background image

Installation and Setup

Internal Track Assembly (optional equipment)

3

3-29

WMDKdoc020322

Installation and Setup

3.11 Internal Track Assembly (optional equipment)

IMPORTANT!

Make sure to align the tracks in the kiln chamber and those outside. Failure

to ensure that the inner and outer tracks are aligned and level may result in difficulty in
loading and unloading the kiln.

Place internal track modules starting inside the doorway at 310mm from the door
opening. This will ensure the doors will close when the removable connecting track is
removed.

Lay the tracks to the back of the kiln. Place the flat cross ties in position. Bolt the cross
ties to the tracks using the M10x16 bolts supplied, starting at the door (front) end of the
kiln.

There is no tie bar closest to the door.

If necessary, cut the last track assembly to match the length of the kiln chamber.

The last tie bar is an angle stop bar closest to the back wall.

FIG. 3-30

1065mm

310mm

External Track

Removable

Track

Wooden

Bearer

Internal Track

«
...
38
39
40
41
42
...
»

Содержание MK20-2























































































Отзывы:

Нет отзывов

Похожие инструкции для MK20-2

Бренд: Daewoo Страницы: 20

Бренд: Euromaid Страницы: 33

Бренд: Sencor Страницы: 5

Global Design 815U

Бренд: Toastmaster Страницы: 16

Бренд: Alliance Laundry Systems Страницы: 87

Бренд: Chefman Страницы: 31

Бренд: Beko Страницы: 84

Бренд: Beko Страницы: 44

Бренд: Beko Страницы: 44

Бренд: Beko Страницы: 84

Бренд: Tricity Bendix Страницы: 14

Бренд: AEG Страницы: 64

Бренд: Kambrook Страницы: 12

Бренд: Kalorik Страницы: 32

Бренд: Kalamera Страницы: 8

Бренд: V-ZUG Страницы: 6

Бренд: PROOX Страницы: 4

Бренд: inventum Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды