Wood-mizer MK20-2 Скачать руководство пользователя страница 10

Страница: 10 / 86

Safety

Safety Instructions

2-3

WMDKdoc020322

Safety

KEEP HANDS AWAY

WARNING!

Always keep clear of exiting hot air through the

exhaust system. Keep hands, feet and any other objects away
from the exhaust when operating kiln. Failure to do so may result in
serious injury.

USE PROPER PROCEDURE WHEN CONDUCTING ELECTRICAL SAFETY CHECKS
AND MAINTENANCE

DANGER!

Make sure all electrical installation, service and/or

maintenance work is performed by a qualified electrician and is in
accordance with applicable electrical codes.

DANGER!

Hazardous voltage inside the electric disconnect box,

starter box, and at the fans can cause shock, burns, or death.
Disconnect and lock out power supply before servicing! Keep all
electrical component covers closed and securely fastened during
kiln operation.

WARNING!

Consider all electrical circuits energized and

dangerous.

WARNING!

Never assume or take the word of another person that

the power is off; check it out and lock it out.

WARNING!

Do not wear rings, watches, or other jewelry while

working around an open electrical circuit.

WARNING!

Voltage is still present in the condensing fans even

when the fans are not running and in many places in the control
cabinet such as the fuses when the control box is off.

Содержание MK20-2























































































Результаты поиска

Содержание MK20-2

Отзывы:

Похожие инструкции для MK20-2

Бренды по названию

Популярные бренды

Wood-mizer MK20-2, Руководство по установке и эксплуатации

Результаты поиска

Содержание MK20-2

Отзывы:

Похожие инструкции для MK20-2

Бренды по названию

Популярные бренды