background image

 

Bedienungsanleitung Steuerung S4_2006_09_25-neu.doc 

Page 9 / 83 

© wodtke GmbH Tübingen. All rights reserved. Subject to change without notice. 

Month of issue xx/2007 

Art. No. 950 281 

3  Hardware and Functional Description 

3.1  Type plate and serial number  

Below is an example of a type plate (Smart Waterplus):  

 

 
The location of the type plate differs between models, as follows:  
Appliance type  

Position of type plate  

Smart Airplus / Waterplus  

Inside of fuel hopper  

Frank Airplus  

Inside of fuel hopper  

CW 21 Airplus / Waterplus 

Inside of fuel hopper  

Airplus insert stove “PE” /  
Waterplus insert stove “PE” 

Inside  of  firedoor  +  front  right  foot  (behind 
inlet grille)  

 

Inside  of  firedoor  +  front  right  foot  (behind 
inlet grille)  

Topline Airplus / Waterplus 

Underside of fuel hopper lid  

 
Important Note:  
Please  make  a  note  of  the  serial  number  stated  on  the  type  plate  of  your  stove  immediately 
after  its  initial  operation  and  keep  the  invoice  in  a  safe  place.  To  provide  spare  parts  or 
respond to guarantee claims we always  need the serial number of the appliance
 so that 
we can be sure of getting the correct spare parts for you. Without a serial number and without 
the date of purchase we are also unable to accept guarantee claims or exclude wrong delivery. 
Please keep all the documents delivered together with your appliance in a safe place for as long 
as  you  own  it.  This  facilitates  customer  service  and  will  also  be  appreciated  by  a  subsequent 
owner should you ever pass the appliance on to someone.  
 
 
Please enter the serial number of your appliance here: _____________________ 

3.2  Scope of delivery  

The following accessories are contained in the delivery:  
 

  Ash scraper, glass cleaner, cleaning brush, instructions  

  Door opener or key (only with Smart/CW 21/Frank/insert stove PE)  

  Felt pads for appliance feet (only with models of the Smart series)  

  Air bleed key (only with Waterplus appliances)  

6-digit serial 
number of the 
appliance
 

Содержание CW 21 Airplus PO 04.7 E




















































































Отзывы: