WMF 1500S+ Скачать руководство пользователя страница 36

Страница: 36 / 120

User Manual WMF 1500 S +

Software | “Ready to operate” display

4.2.3 SteamJet cup warmer

Burn hazard / scalding hazard

•

Hot steam is produced by the SteamJet cup
warmer. The cups and adjacent surfaces also
get very hot.

> Use heat-resistant cups.

> Always place a cup upside-down over the cup

warmer before dispensing steam.

> Do not touch the adjacent surfaces

immediately after dispensing.

> Do not touch the spouts immediately after

dispensing.

> Never use the SteamJet function without the

drip grid in place or without the cup warmer
insert.

Health hazard / hygiene

•

The SteamJet function is intended for
warming the drinking vessel and is not
intended to be used for cleaning.

> Always use freshly washed drinking vessels

when warming cups.

The SteamJet cup warmer can use steam to warm
up cups.

Place a cup on the cup warmer with the opening
facing downward

Touch the pad

Hot steam slowly flows into the cup from below.
The jet of steam stays on for the time set in the
settings.

Touch the SteamJet pad again

The steam jet stops immediately.

CaUtion

Follow the Safety chapter

starting on page 7

Clean drip tray daily
Care

starting on page 70

CaUtion

Follow the Safety chapter

starting on page 7

SteamJet pad active/inactive

Operating options

page 48

Содержание 1500S+

























































































































Результаты поиска

Содержание 1500S+

Отзывы:

Похожие инструкции для 1500S+

Бренды по названию

Популярные бренды

WMF 1500S+, Руководство пользователя

Результаты поиска

Содержание 1500S+

Отзывы:

Похожие инструкции для 1500S+

Бренды по названию

Популярные бренды