Winco DX100F4, Инструкция по установке и эксплуатации

Страница: 6 / 24

6
OPM-115
REV A
INTRODUCTION
PRODUCT DESCRIPTION
This engine-generator set is designed for unattended remote start
operation. It can be operated as part of a fully automatic standby power
system or independently as a local start unit in a prime power system.
The engine-generator set is fully tested at the factory prior to shipment
to insure proper operation of each individual component as well as the
total system’s performance and reliability.
The engine generator set consists of a multi-cylinder, liquid cooled
engine nominally operating at 1800 rpm. The generator frequency
regulation is maintained by the engine governor to /- 1.5 Hz
(cps), from no load to rated load for standard mechanical governors
and to /- .5 Hz or better for units equipped with an electronic
governor. The generator is a single bearing, direct drive, rotating field
design. The generator is connected to the engine flywheel via flexible
drive disks. Generator set is skid mounted with isolation mounts
between the engine and base on all units.
A customer supplied 12 Volt battery is required to complete the
installation, the DX250-350 are 24 Volt systems. Battery requirements
are listed later under the battery installation section.
Unit Orientation Note: All references used in this manual for unit
familiarization, access and component locations on the Generator Set
are oriented from a TOP (plan) VIEW with engine at the FRONT and
generator to the REAR.
WINPOWER uses a common junction box for all customer control and
power connections (both AC output and DC control). The common
electrical junction box is always on the left side at the generator end of
the machine.
The engine is controlled and Generator Set operation is monitored for
safe operation by a programmable microprocessor based electronic
Engine Control Module (ECM) with an LCD digital display. The
generator set ECM control is mounted on a vertical pedestal on the
right side of the generator. The ECM is programmed with a cycle
cranking sequence - 3 cycles of 15 seconds on/15 seconds off, and
5 minute cool-down delay. The cool-down delay can be changed in
the field from 0 to 30 minutes by your installer. Other features, timing
Stamford Newage Model# UCI274H (12 lead)
Voltage Regulator SX460
Rotor Resistance 1.82 ohms
Stator Resistance 0.0155 ohms/phase
Excitor Stator Resistance 20.0 ohms
Excitor Rotor Resistance 0.091 ohms/phase
Stamford Newage Model# HCI434D (12 lead)
Voltage Regulator MX341
Rotor Resistance 1.05 ohms
Stator Resistance 0.00124 ohms/phase
Excitor Stator Resistance 18.0 ohms
Excitor Rotor Resistance 0.068 ohms/phase
cycles, set points, and signal output capabilities are possible. Consult
factory for procedure and passwords.
NOTICE:
These units will automatically transfer if a power outage occurs while
running in exercise mode.
GENERATOR SET
Every WINCO generator set has its own unique identity data plate.
This data plate identifies the complete unit model number, the system
serial number, and has links to the individual components that form the
generator set in our factory records. Several of the major components
also have their own individual data plates providing additional
information to document build data for warranty and replacement parts.
ENGINE
Refer to the engine operators manual for more detailed operation and
maintenance information.
CAUTION: EQUIPMENT DAMAGE:
Be sure to check the engine oil level frequently as specified in the
engine manual.
The engine manufacturer has established an excellent worldwide
engine service organization; engine service is available from a nearby
authorized dealer or distributor. Go to the WINCO website for a list of
engine dealers (http://wincogen.com/Engine_Support) or contact the
WINCO Service Department.
The rated power of each engine-generator is limited by the
temperature, altitude, and all other ambient conditions specified by
the engine manufacturer. Engine power may decrease 3½% for each
1000 feet above sea level, and will decrease an additional 1% for each
10 degrees Fahrenheit above 60° Fahrenheit. Units should not be
operated in ambient temperature greater than 125° Fahrenheit.
GENERATOR
WINCO generator sets use brushless, AVR (Auto-Voltage Regulator)
controlled broad-range generator ends. The generator converts
rotational mechanical energy into electrical energy. These WINCO units
are equipped with generators manufactured by Cummins Generator
Technology. Each generator ‘end’ has its own data tag. A unique serial
number is on the data plate.
MODEL NUMBER STRUCTURE
The WINPOWER alpha-numerical numbering consists of a base model
designation, followed by an options section, separated by a dash mark.
The base component of the model numbering system identifies an
engine type, engine starting method, fuel type, kilowatt rating, engine
manufacturer, and number of generator poles. Following the separation
dash mark is the voltage connection and optional installed equipment.
Options include features like, weather enclosures (housing), base
mounted fuel tank sizes, and trailer options.
Please note that some features or packages, such as NFPA level I
& II, do not have an indication place in this numbering system. They
are issued and built with an M-Spec (i.e. M-10372) number which can