White Mountain Hearth DVP36FP3 Series Скачать руководство пользователя

Страница: 35 / 68

23340-2-1007

Page 35

the opposite end. Do not crimp or enlarge tube.

8. Attach the 4” (102mm) diameter ﬂue outlet tube onto the rigid

venting system or directly to ﬁreplace. Ensure the 4” (102mm)

diameter ﬂue outlet tube is placed as far as possible onto the rigid

venting system. Mark the 4” (102mm) diameter ﬂue outlet tube

2 1/2” (64mm) beyond the vinyl siding kit or wall. S

ee Figure

54.

Remove the 4” (102mm) diameter ﬂue outlet tube from rigid

venting system. When installing directly to ﬁreplace, tape gasket

needs to be used.

9. Mark or wrap tape completely around the tubes at the marked points

to help in making a true cut. Do not crimp or enlarge tubes.

10. From outside: Push the 6 5/8” (168mm) diameter inlet tube/mount-

ing plate onto end of rigid venting system to correct position. Fasten

the outside mounting plate to the vinyl siding kit or wall with (4)

10 x 1 1/2” screws. (Ensure upward slope).

11. From inside: Attach the inlet tube to the collar on the back of

the ﬁreplace (or the rigid venting system) using (3) self tapping

screws.

12. Seal the 4” (102mm) diameter ﬂue outlet tube. Follow instructions

and diagram (

Figure 56

13. Fasten 4” (102mm) diameter ﬂue outlet tube in place. Do not “twist”

the ﬂue outlet tube into the ﬁreplace collar (or rigid venting sys-

tem). Hold the tube by the seam and push in using a perpendicular

“rocking” motion. This ensures the seam on the tube stay intact.

14. Fasten vent cap end using (3) 10 x 1/2” screws to mounting plate.

Sealing 4” (102mm) Diameter Flue Outlet Tube

7. Remove outside mounting plate with tube attached from wall. Mark

and cut the extra length of the 6 5/8” (168mm) diameter tube from

OUTSIDE WALL

MEASURE

VINYL SIDING KIT DV822

OUTSIDE MOUNTING

PLATE

EXT. WALL
SURFACE OR
VINYL SIDING KIT

FLUE
PIPE

CUT
2 ½”

BEYOND EXTERNAL

WALL SURFACE OR

VINYL SIDING KIT

Figure 54

Figure 55

1”

VENT CAP END

APPLY SEALANT

ON THE INSIDE

DO NOT PLACE

OVERLAPPED

SECTION OVER

THE SEAM IN THE TUBE

Figure 56

Note:

Tape gasket to be applied prior to installing to ﬁreplace ﬂue outlet tube

only. Tape gasket should not be used when mating the ﬂue outlet tube to a rigid

venting system.

DVVK-4RE VENT KIT INSTALLATION INSTRUCTIONS (continued)

Содержание DVP36FP3 Series





































































Результаты поиска

Содержание DVP36FP3 Series

Отзывы:

Похожие инструкции для DVP36FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVP36FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVP36FP3 Series

Отзывы:

Похожие инструкции для DVP36FP3 Series

Бренды по названию

Популярные бренды