manualshive.com logo in svg

White Mountain Hearth DVP36FP3 Series, Инструкция по установке и руководство пользователя

Поделиться
Скачать
White Mountain Hearth DVP36FP3 Series Скачать руководство пользователя страница 13

23340-2-1007

Page 13

Flush Wall Installation

Figure 13

Combustible Surround Installation

Figure 14

Attention: Cold climate installation recommendation: When 

installing this unit against a non-insulated exterior wall, it is 

recommended that the outer walls be insulated to conform 

to applicable insulation codes.

Vent Runs (Figures 15, 16, 17, 18, and 19)

In  planning  the  installation  for  the  fireplace,  it  is  necessary  to 

install  certain  components  before  the  appliance  is  completely 

positioned  and  installed. These  include  the  direct  vent  system, 

gas piping for the appliance and the electrical wiring. (If the fan 

option is used.)
The appliance can be mounted on any of the following surfaces:

1. A flat, hard combustible (burnable) surface.

2. A raised wooden platform.

3. Four (4) corner supports. (Example: Four (4) concrete masonry 

blocks.) These supports must be positioned so they contact all 

four (4) perimeter edges on the bottom of the unit.

VERTICAL, 90° ELBOW WITH HORIZONTAL 

TERMINATION

Figure 15

3! OF NON-COMBUSTIBLE MATERIAL

FINISHED WALL

FRONT TRIM OR NON-

COMBUSTIBLE MA TERIAL

(INSTALLA TION IS OPTIONAL)

JOINT BETWEEN FINISHED

WALL AND UNIT SEALED

WITH 300° F, 149° C SEALANT

MATERIAL

(Sealant is optional)

DVP36

49 ½

”

(126 mm)

TO BOTTOM

OF UNIT

VENT CAP/

THIMBLE

THIMBLE

3! OF NON-COMBUSTIBLE MATERIAL

FINISHED WALL

FRONT TRIM OR NON-COMBUSTIBLE

MATERIAL (INSTALLATION IS OPTIONAL)

JOINT BETWEEN FINISHED WALL AND

UNIT SEALED WITH 300° F 149

MATERIAL (SEALANT IS OPTIONAL)

° C

SEALANT

COMBUSTIBLE SURROUND

MANTELSHELF

2 X 4

HEADER

STAND OFF

LP and Nat models

Содержание DVP36FP3 Series





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды