White Mountain Hearth DVP36FP3 Series страница 20 Скачать руководство пользователя

Страница: 20 / 68

23340-2-1007

Page 20

1. Unpack vent components and check all items for shipping

damage.

2. For this venting system to operate as designed it is depen-

dent on the use of all parts and procedures detailed in these

instructions. Failure to follow these instructions may poten-

tially affect the performance of this vent system and the at-

tached appliance.

3. As per the ﬁreplace manufacturer’s instructions, replace the

existing 6 5/8” diameter ﬁreplace vent adapter with the 7”

diameter ﬂex vent ﬁreplace adapter included in the vent kit.

Install the adapter collar with the screws removed from the

standard ﬁreplace collar. Refer to the ﬁreplace manual for ad-

ditional information on the vent collar removal and installa-

tion.

4. Once the ﬁreplace location has been determined, mark the

ceiling where the ﬂex vent will pass through. Cut an opening

for installation of the ﬁrestop thimble assembly. The open-

ing must measure a minimum of 9-1/2” x 9-1/2” square.

See

Figure 27.

5. Next, determine the location for the cutout in the roof open-

ing. This opening must be large enough to provide a mini-

mum 1” air space clearance from the vertical vent pipe to any

combustible framing.

6. Install the Firestop/Thimble assembly to the framed opening

in the ceiling using common nails or screws.

Note:

The thimble assembly is adjustable up or down as

needed within the ﬁrestop. It is also designed with a pivoting

ﬁrestop for use with 0 - 3/12 pitch cathedral ceilings.

7. To begin vent system assembly, ﬁrst layout all the vent com-

ponents on the ﬂoor in the order in which they will be as-

sembled.

8. Stretch the 4” diameter inner ﬂex ﬂue and 7” diameter outer

ﬂex vent to the maximum length of 6 feet.

9. Install the spring spacers provided around the 4” diameter

ﬂex ﬂue at 1 foot intervals, then slide the ﬂue pipe with spac-

ers into the 7” diameter outer ﬂex vent pipe. Make sure the

springs are spaced evenly starting at 12 inches from the ﬁre-

place collar.

See Figure 28.

NAILS
(4) REQ'D.

THIMBLE

FIRESTOP

CEILING FRAMING

9½” Min.

(241mm)

9½” Min.

(241mm)

NOTE: ADDITIONAL
HOLES FOR ADJUSTING
THIMBLE UP OR DOWN
AS NEEDED

FLEX OUTER

AIR INTAKE PIPE

SPACER SPRINGS

FLEX FLUE PIPE

Figure 27

Figure 28

SPACER SPRINGS

4" FLEX
VENT PIPE

12”

305mm

12”

305mm

12”

305mm

12”

305mm

Step-By-Step Installation For Flex DV Kit

DVVK-4FV DIRECT VENT TERMINATION KIT (continued)

Содержание DVP36FP3 Series





































































Результаты поиска

Содержание DVP36FP3 Series

Отзывы:

Похожие инструкции для DVP36FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVP36FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVP36FP3 Series

Отзывы:

Похожие инструкции для DVP36FP3 Series

Бренды по названию

Популярные бренды