White Mountain Hearth DVP36FP3 Series Скачать руководство пользователя

Страница: 29 / 68

23340-2-1007

Page 29

Figure 43

A = *Clearance above grade, veranda, porch, deck or balcony

[*12 inches (30cm) minimum]

B = clearance to window or door that may be opened [*12 inches

(30cm) minimum for appliances < 100,000 Btuh (30kW)

C = clearance to permanently closed window [minimum 12

inches (30cm) recommended to prevent condensation on

window]

D = vertical clearance to ventilated sofﬁt located above the

terminal within a horizontal distance of 24 inches (60 cm) from

the center of the terminal [18 Inches (46 cm) minimum

E = clearance to unventilated soffit [12 inches 30cm)

minimum]

F = clearance to outside corner.

See Page 28.

G = clearance to inside corner.

See Page 28.

H = *not to be installed above a meter/regulator assembly

within 3 feet (90cm) horizontally from the center-line of

the regulator

I = clearance to service regulator vent outlet [*6 feet (1.8m)

minimum]

J = clearance to non-mechanical air supply inlet to building or

the combustion air inlet to any other appliance [*12 inches

(30cm) minimum for appliances ≤ 100,000 Btuh (30 kW)

36 inches (90cm) minimum for appliances > 100,000 Btuh

(30kW)]

K = clearance to a mechanical air supply inlet [* 6 feet (1.8m)

minimum]

L = †clearance above paved sidewalk or a paved driveway located

on public property [*7 feet (2.1m) minimum]

M = clearance under veranda, porch, deck, or balcony [*12 inches

(30cm) minimum ¥]

† a vent shall not terminate directly above a sidewalk or

paved driveway which is located between two single family

dwellings and serves both dwellings*

¥ only permitted if veranda, porch, deck, or balcony, is fully

open on a minimum of 2 sides beneath the ﬂoor*

* as speciﬁed in CGA B149 Installations Codes or ANSI

Z223.1. Note: Local Codes or Regulations may require

different clearances.

VENT CLEARANCES

Содержание DVP36FP3 Series





































































Результаты поиска

Содержание DVP36FP3 Series

Отзывы:

Похожие инструкции для DVP36FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVP36FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVP36FP3 Series

Отзывы:

Похожие инструкции для DVP36FP3 Series

Бренды по названию

Популярные бренды