White Mountain Hearth DVP36FP3 Series Скачать руководство пользователя

Страница: 16 / 68

23340-2-1007

Page 16

Figure 22

Examples of possible venting systems using two (2) 90° elbows. V

is listed as minimum vertical dimensions and H1 + H2 is listed as

total of maximum horizontal dimensions. The maximum vertical

and horizontal distances for two (2) 90° elbows as shown in Figure

23 is 20 feet.
Attention: Refer to Figure 20 for additional venting

requirements.

Figure 22

Below Grade Installation

When it is not possible to meet the required vent terminal clearances

of 12" (305mm) above grade level, a snorkel kit is recommended.

It allows installation depth down to 7" (178mm) below grade level.

The 7" (178mm) is measured from the center of the horizontal vent

pipe as it penetrates through the wall.
Ensure the sidewall venting clearances are observed. If venting

system is installed below ground, we recommend a window well

with adequate and proper drainage to be installed around the

termination area.

TYPICAL BASEMENT INSTALLATION

Figure 21

Examples of possible venting systems using one (1) 90° elbow.

Eight (8) feet is listed as minimum vertical vent run with 20 feet

of maximum horizontal vent run. Vertical dimensions are based on

centerline to centerline of pipe. Horizontal dimensions are based

on centerline of pipe to end of termination.

Firestop at

Ceiling Level

Firestop at

Ceiling Level

VENTING FIREPLACE - TOP (continued)

LP and Nat models

Содержание DVP36FP3 Series





































































Результаты поиска

Содержание DVP36FP3 Series

Отзывы:

Похожие инструкции для DVP36FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVP36FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVP36FP3 Series

Отзывы:

Похожие инструкции для DVP36FP3 Series

Бренды по названию

Популярные бренды