White Mountain Hearth DVP36FP3 Series страница 41 Скачать руководство пользователя

Страница: 41 / 68

23340-2-1007

Page 41

Initial Lighting

Upon completing the gas line or turning the gas valve on after it

has been in the “OFF” position, a small amount of air will be in the

lines. When ﬁrst lighting the ﬁreplace, it will take a few minutes

for the lines to purge themselves of this air. Once the purging is

complete, the ﬁreplace will light and operate satisfactorily.
Subsequent lightings of the appliance will not require such purging

if the gas valve is not turned to “OFF.”

Pilot Flame (Figure 65)

The thermopile/thermocouple (standing pilot) tips should be

covered with ﬂame.

Figure 65

750 Millivolt System

The standing pilot (750 millivolt system) is a continuous burning

pilot. The pilot remains ON even when the main burner is OFF.
When you ignite the pilot, the thermopile produces millivolts

(electrical current) which energizes the magnet in the gas valve.

After 30 seconds to 1 minute time period you can release the gas

control knob and the pilot will stay ON. Allow your pilot ﬂame to

operate an additional one (1) to two (2) minutes before you turn the

gas control knob from the PILOT position to the ON position. This

time period allows the millivolts (electrical current) to build-up to

a sufﬁcient level allowing the gas control to operate properly.
1. Follow the SAFETY and LIGHTING INSTRUCTIONS for

standing pilot controls found in this manual and on labels found

in control compartment behind the door assembly.

CAUTION: During the initial purging and subsequent lightings,

never allow the gas valve control knob to remain depressed in

the “pilot” position without pushing the piezo ignitor button

at least once every second.

2. During the operating season, leave the control valve knob in the

“ON” position. This will allow the pilot ﬂame to remain lit. Turn

the burner ﬂame on or off with the ﬁreplace REMOTE/OFF/ON

switch, wall switch or remote controls.

NOTE:

The gas control valve allows you to increase or decrease the

height of the main burner ﬂame. The control valve has a pressure

regulator with a knob as shown in Figure 64. Rotate the knob

clockwise to “HI” to increase the ﬂame height and counterclockwise

to “LO” to decrease the ﬂame height.
3. When the operating season is over, turn the REMOTE/OFF/ON

switch to “OFF” and the control valve to “OFF”. The system,

including the pilot light, will be shut down.

Figure 64

The OWNER should carefully read and follow these operating

instructions at all times. Lower the door assembly to view the gas

controls for the ﬁreplace.

CONTROL KNOB

HI/LO REGULATOR

OPERATING INSTRUCTIONS

Содержание DVP36FP3 Series





































































Результаты поиска

Содержание DVP36FP3 Series

Отзывы:

Похожие инструкции для DVP36FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVP36FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVP36FP3 Series

Отзывы:

Похожие инструкции для DVP36FP3 Series

Бренды по названию

Популярные бренды