White Mountain Hearth DVP36FP3 Series страница 28 Скачать руководство пользователя | Manualshive

Страница: 28 / 68

background image

23340-2-1007

Page 28

Termination clearance for buildings with combustible and noncombustible exteriors.

Vertical Sidewall Installations

Important! Minimum clearance between vent pipes and combustible materials is three (3") (76mm) on top, and (1") (25mm) on bottom

and sides.

Important!

When vent termination exits through foundation less than 20" below siding outcrop, the vent pipe must ﬂush up with the

siding. SD-985 termination cap must be used.

Information on Various Venting Routes and Components

Important:

It is always best to locate the ﬁreplace in such a way that minimizes the number of offsets and horizontal vent length.

Since it is very important that the venting system maintain its balance between the combustion air intake and the ﬂue gas exhaust, certain

limitations as to vent conﬁgurations apply and must be strictly adhered to.
The graph showing the relationship between vertical and horizontal side wall venting will help to determine the various vent lengths

allowable.
The horizontal vent run refers to the total length of vent pipe from the ﬂue collar of the ﬁreplace to the face of the outer wall.
The maximum horizontal vent run is 20 feet (457 cm) when the vertical vent rise is 8 feet (244 cm).

See Figure 20.

Venting terminals shall not be recessed into wall or siding.

Figure 42

TERMINATION CLEARANCES

«
...
26
27
28
29
30
...
»

Содержание DVP36FP3 Series





































































Отзывы:

Нет отзывов

Похожие инструкции для DVP36FP3 Series

Бренд: barbas Страницы: 32

Cosi square glass set M

Бренд: Gimeg Страницы: 2

Abbotsford 064-4015-0

Бренд: Canvas Страницы: 104

Бренд: United States Stove Страницы: 44

Бренд: FMI Страницы: 20

Бренд: Mosaic Страницы: 17

Бренд: ADURO Страницы: 14

Бренд: QualityCraft Страницы: 4

Бренд: Nordpeis Страницы: 70

Бренд: Superior Страницы: 28

Бренд: komodo Страницы: 32

Бренд: Astria Fireplaces Страницы: 34

Бренд: KAL-FIRE Страницы: 16

GreenSmart Fireplace 564 SS

Бренд: Travis Industries Страницы: 28

Бренд: Travis Industries Страницы: 3

Бренд: Travis Industries Страницы: 2

Бренд: Travis Industries Страницы: 5

Бренд: Travis Industries Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды