PAGE 4
FOR SERVICE TECHNICIAN’S USE ONLY
DO NOT REMOVE OR DESTROY
Commanding Loads ‘On’ and ‘Off’
in Service Test Mode
With the desired load’s number on the ETR
display, the load can be toggled on and off by
pressing the START button. Each press will
toggle the state of the load from ‘off’ to ‘on’ or
from ‘on’ to ‘off’.
NOTE:
Activating any of the
spin or agitate functions will result in functions
10–14 reporting their status as ‘on’ because
reported status is based on motor motion
being commanded.
Failure to Turn Load On Indication
If the number of loads (pumps, valves, and
motor) allowed on at the same time or the
conditions to actuate the load are not correct,
the display will turn off momentarily and an
invalid tone will sound.
The chart below indicates load and test cycle
function numbers:
Load and Test Cycle Function Numbers Chart
NOTE:
Some loads will not be available on all models
Display
Function
Notes
000
Toggle Lid Lock
Note:
To lock or unlock the lid, all loads (pumps, motor,
valves, and heater) must be off and the lid must be closed.
001
Toggle Cold Valve
002
Toggle Hot Valve
003
Toggle Fresh Fill Valve
N/A
004
Toggle Detergent Valve
N/A
005
Toggle Fabric
For water to flow, cold water should be turned on first.
Softener
Valve
Note:
If the fabric softener valve is turned “ON” without the
cold water valve “ON”, water can overflow the front of the tray.
006
Toggle Oxi Valve
For water to flow, hot water should be turned on first.
Note:
If the Oxi valve is turned “ON” without the hot water valve
“ON”, water can overflow the front of the tray.
Note:
Oxi not available on all models.
007
Toggle Bleach Valve
Note:
On models with dump bleach dispenser, toggling this load
will turn on the Oxi valve.
008
Toggle Drain Pump
009
Toggle Recirc. Pump
Note:
Not available on all models.
010
Toggle Low
Lid must be closed and locked for this to be enabled.
Speed
Spin
Note:
The basket must be empty for this function.
011
Toggle Mid
Lid must be closed and locked for this to be enabled.
Speed
Spin
Note:
The basket must be empty for this function.
012
Toggle High
Lid must be closed and locked for this to be enabled.
Speed
Spin
Note:
The basket must be empty for this function.
013
Toggle Slow Agitate
Lid must be closed and locked for this to be enabled.
Note:
The basket must be empty for this function.
014
Toggle Fast Agitate
Lid must be closed and locked for this to be enabled.
Note:
The basket must be empty for this function.
015 Toggle
Shifter
Switch in and out of Spin. Shifter On = Spin and Shifter Off =
Agitate.
Note:
This can only be commanded while the motor is
not running. The shifter will also be on when spin functions
10–12 are active.
016
Toggle Basket Light
N/A
017 Toggle
Heater
Note:
To actuate the heater, all loads (pumps, motor, and valves)
must be off and water level must be above the impeller.
050
Run Factory Calibration
Note:
For factory test only.
051
Service Diagnostics
Service Diagnostics for repair verification and installation
verification.
052
Run Service Calibration
This calibrates the main control to the washer for optimal load size
sensing. Upon completion, the UI will display 000. The Soil Level
and Temp buttons can be used to review step results if Pass/Fail
criteria exist. If a step has no Pass/Fail criteria, --- will be displayed.
053
Run Dry Factory
Note:
For factory test only.
Calibration
075
Set Life Test Mode
Note:
For factory test only. If life test mode is accidentally
activated,
Life Test can be exited by removing power from the
washer and waiting for the control to power down as indicated
by the diagnostic LED ceasing to flash (see Figure 1, page 2).
