53
If you experience
Possible Causes
Solution
Error Code Appears in Display (for 2- and 3-digit displays)
Once any possible issues are corrected, touch POWER once to clear the code. Reselect and restart the cycle.
“Sd” or “Sud”
(excess suds) appears
in display
Excessive suds in washer dryer.
Washer dryer is running a suds-
reduction routine.
Allow the washer dryer to continue. Use only HE detergent. Al-
ways follow the detergent manufacturer’s instructions to deter-
mine the amount of detergent to use and base detergent quan-
tity on load size. Not all detergents labeled as High Efficiency
are identical in formulation and their ability to reduce suds. For
example, natural, organic, or homemade HE detergents may
generate a high level of suds. If you use one of these and see
an
“Sd” or “Sud”
error code appear in the display, consider
using a different HE detergent.
“
Lo
”
followed by
“
FL
”
or
“
F8
”
followed by
“
E1
”
or
“
Lo
”
followed by
“
FL
”
or
“
F08
”
followed by
“
E01
”
(water supply error)
appears in display
Check for proper water supply.
Unit will drain for 8 minutes while door remains locked. The
drain cycle must be allowed to complete or the error code
cannot reset. When complete, touch POWER once to clear the
code. Then touch POWER again to restart washer dryer.
If code appears again, call for service.
Both hoses must be attached and have water flowing to the
inlet valve.
Both hot and cold water faucets must be ON.
Check that inlet valve screens are not clogged.
Remove any kinks in the inlet hose.
If used, auto shut-off connectors and hoses must be properly
installed and in working order.
Check for proper inlet hoses.
Use only manufacturer’s recommended inlet hoses.
“
F9
”
followed by
“
E1
”
or
“
F09
”
followed by
“
E01
”
(drain pump system
error) appears in display
Check plumbing for correct drain
hose installation. Drain hose extends
into standpipe farther than
4
1
⁄
2
" (11.4 cm).
Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor.
Not using HE detergent or using too
much HE detergent.
Use only HE detergent. Always measure detergent and follow
manufacturer’s directions based on load size and soil level.
“
F5
”
followed by
“
E2
”
or
“
F05
”
followed by
“
E02
”
(door will not lock)
appears in display
Washer dryer door not locking.
Touch POWER to cancel the cycle. Check that the door is
closed completely and latching. Check for items in the washer
dryer drum that may be keeping the door from closing
completely.
“rL”
(remove load)
appears in display
Load detected in drum during Clean
Washer with affresh cycle.
Remove items from washer dryer drum and restart Clean
Washer with affresh cycle.
"PF"
Appears upon recovery from power
loss, if power was lost while running
a cycle.
Touch POWER once to clear the code. Then touch POWER
again and restart the washer dryer.
TROUBLESHOOTING
First try the solutions suggested here or visit our website at
www.whirlpool.com.tw
Содержание 8TWFC6810LW
Страница 63: ...63 NOTES ...
Страница 64: ...W11516195A 2021 年 6 月 2021保留所有權利 All rights reserved 06 21 ...