manualshive.com logo in svg

Whelen Engineering Company IPS 400, Руководство по эксплуатации продукта

Поделиться
Скачать
Whelen Engineering Company IPS 400 Скачать руководство пользователя страница 40

continued......

30H  Clear

Clears any event in progress.

31H  Message 1

Initiates digital voice message 1, for an RSDVM module.

32H  Message 2

Initiates digital voice message 2, for an RSDVM module.

33H  Message 3

Initiates digital voice message 3, for an RSDVM module.

34H  Message 4

Initiates digital voice message 4, for an RSDVM module.

35H  Message 5

Initiates digital voice message 5, for an RSDVM module.

36H  Message 6

Initiates digital voice message 6, for an RSDVM module.

37H  Message 7

Initiates digital voice message 7, for an RSDVM module.

38H  Message 8

Initiates digital voice message 8, for an RSDVM module.

39H  Strobe On 

Activates the Strobe Light

3AH  Strobe Off 

De-activates the Strobe Light

3BH  Message 9

Initiates digital voice message 9, for an RSDVM module.

3CH  Message 10

Initiates digital voice message 10, for an RSDVM module.

3DH  Message 11

Initiates digital voice message 11, for an RSDVM module.

3EH  Message 12

Initiates digital voice message 12, for an RSDVM module.

3FH  Active Status 

Requests multiple system status parameters

NOTES:

Commands 09 to 0F are only for rotating sirens, such as the WPS-4000 Series.
Commands 1C and 1D apply to factory installed radio transceiver systems only.
Command 27 to 2F to be used only with a factory supplied weather station.
Commands 39 and 3A used only with a factory supplied strobe light or StrobeVisor.
Command 3F, Moscad use only.

Содержание IPS 400













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды