manualshive.com logo in svg

Whelen Engineering Company IPS 400, Руководство по эксплуатации продукта

Поделиться
Скачать
Whelen Engineering Company IPS 400 Скачать руководство пользователя страница 4

Table of Contents

Section 1 

INTRODUCTION .............................................................................................. 2

1.0

Introduction to the IPS ..................................................................................................... .2

1.1

Using This Manual ...........................................................................................................2

Section 2 

IPS CONTROLLER DESCRIPTION ............................................................... 3

2.0

Controller System Description...........................................................................................3

2.1

Physical Description........................................................................................................ ..3

2.2

Operational Description ....................................................................................................4

2.2.1

System Activation/Control Methods ..................................................................................4

2.2.2

Timing Selection and Duration .........................................................................................4

2.2.3

Audio Characteristics of Warning Signals.........................................................................4

Section 3 

SPECIFICATIONS............................................................................................. 5

3.0

General Specifications...................................................................................................... .5

Section 4 

MODULE DESCRIPTION ................................................................................ 6

4.0

IPS Module Descriptions...................................................................................................6

4.1

ESC-864 (Controller)........................................................................................................6

4.1.1

Local Controls and LED Indicators ...................................................................................6

4.1.2

ESC-864 Controller Circuit Board ....................................................................................9

4.1.3

Tone Generator .................................................................................................................9

4.1.4

Digital Voice (option) .......................................................................................................9

4.1.5

Landline or RF Link Interfaces (options)...........................................................................9

4.1.6

DTMF Formats .................................................................................................................9

4.1.7

Radio Receiver/Transceiver (option) ............................................................................... 11

4.1.8

Local Microphone Input and Volume Control ................................................................. 11

4.1.9

System Diagnostics ......................................................................................................... 11

4.2

Power Amplifier Operation ............................................................................................. 11

4.2.1

Speaker Configurations................................................................................................... 12

4.3

System Driver Board ....................................................................................................... 13

4.3.1

Audio Signal Distribution ............................................................................................... 13

4.3.2

IPS Silent Test Operation ................................................................................................ 13

4.3.3

Power Saving Logic ........................................................................................................ 14

4.3.4

DC Voltage Regulation ................................................................................................... 14

4.4

Battery Charger Operation .............................................................................................. 14

4.5

Batteries.......................................................................................................................... 14

Section 5 

INSTALLATION.............................................................................................. 15

5.0

Installation Instructions...................................................................................................15

5.1

Site Selection .................................................................................................................. 15

5.2

Receiving/Unpacking the IPS.......................................................................................... 17

5.3

Installation of the IPS Cabinet......................................................................................... 17

5.3a

Installation of the “Type C” Cabinet................................................................................ 18

5.4

Conduit Openings for the IPS Cabinet............................................................................. 19

5.5

AC Wiring ...................................................................................................................... 20

5.6

Speaker Wiring ............................................................................................................... 21

5.7

Radio Option................................................................................................................... 22

Section 6 

BATTERIES ..................................................................................................... 23

6.0

Battery Installation.......................................................................................................... 23

Содержание IPS 400













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды