manualshive.com logo in svg

Whelen Engineering Company IPS 400, Руководство по эксплуатации продукта

Поделиться
Скачать
Whelen Engineering Company IPS 400 Скачать руководство пользователя страница 16

12

electrical circuit between a power amplifier channel and its respective speakers. The LEDs, indicate a complete circuit
from the respective power amplifier channel to the speakers and back when the power amplifier is in operation. An
active LED indicates that the power amplifier channel, system driver board, speaker wires, and speaker(s) are
functioning when a warning signal tone or public address mode is active. Speakers < 60 Watts may not indicate
correctly.

In the public address mode of operation, each appropriate power amplifier channel(s) increases its amplification output
by an additional 25% to compensate for the differential in power between voice audio signals and siren warning signals.
This increase in amplification assists in providing voice broadcasting at warning signal tone ranges.

4.2.1  Speaker Configurations

The IPS power amplifier(s) can be connected to various speakers and speaker configurations or arrangements. The table
below shows some common speakers and the number of speakers allowed per each 100 W channel on each power
amplifier.

Common Speakers and Speaker Arrangements

SPEAKER DESCRIPTION

MAXIMUM SPEAKERS
PER CHANNEL

The WS15T/WS30T are weatherproof, 15 to 30 watt re-entrant loud speakers
with multi-tapped transformers for output adjustments. The WS15/WS30 do not
have transformers.

6: WS15T or WS15
3: WS30T or WS30

The WS15TR/WS15TEN are 15 watt re-entrant loudspeakers with multi-tapped
transformers for output adjustment. The WS15TR speaker is ideal for recessed
mounting applications. The WS15TEN speaker is for recessed mounting in
ceiling tiles.

5: WS15TR
5: WS15TEN

The WS100 heavy duty, 100 W re-entrant loud speaker with a wide-angle horn.

1: WS100

The WS100TCH Heavy Duty weatherproof, 100 watt wide-angle re-entrant
speaker with multi-tapped transformer output adjustment. The WS100CH does
not have the transformer.

1: WS100TCH or

1: WS100CH

The WSXPL60T loud speaker is used in areas having explosive or combustible
atmospheres. The speaker is UL and CSA listed, 60 W re-entrant, wide-angle
loud speaker and has a multi-tapped transformer.

1:WSXPL60T

Individual product descriptions may be requested from the sales office, for each speaker in the table.

Содержание IPS 400













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды