manualshive.com logo in svg

Whelen Engineering Company IPS 400, Руководство по эксплуатации продукта

Поделиться
Скачать
Whelen Engineering Company IPS 400 Скачать руководство пользователя страница 25

21

5.6  Speaker Wiring

All of the speakers audio
connections are made through the
System Driver Board, located on the
left side of the back wall of the IPS
cabinet.

The upper most terminal block is
TB1. It is the connection point for
the audio signals to the speakers (for
direct connect speakers) or to the
speakervisors (for supervised
speakers). Refer to the drawing.
Starting at the top, notice that the
terminals are in pairs, 1 through 8.
Also notice that each pair has a (+)
terminal and a (-) terminal. Each
terminal pair can drive up to 100
watts, therefore, speaker loads
greater than 100 watts must be
distributed through more than one
terminal pair.

TB2 is not used.

TB3 is not used.

Remember to keep track of the audio
cables and cable polarity. The audio
cable must be connected to the
proper polarity at each speaker.

J6

J3

J4

J5

J1

F1

J2

SW1

TB2

TB1

TB3

3 AMP

PC. BD #67729

.325 CENTERS

.250 CENTERS

SPEAKER AUDIO 1+

SPEAKER AUDIO 1-

SPEAKER AUDIO 2-

SPEAKER AUDIO 2+

SPEAKER AUDIO 4+

SPEAKER AUDIO 4-

SPEAKER AUDIO 3-

SPEAKER AUDIO 3+

SPEAKER AUDIO 7+

SPEAKER AUDIO 7-

SPEAKER AUDIO 8-

SPEAKER AUDIO 8+

SPEAKER AUDIO 6+

SPEAKER AUDIO 6-

SPEAKER AUDIO 5-

SPEAKER AUDIO 5+

Содержание IPS 400













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды