![background image](http://html1.mh-extra.com/html/westomatic/easy-6000/easy-6000_operator-and-installation-manual_965969025.webp)
24
EASY 6000
– Issue 02
FAS INTERNATIONAL S.p.A. Via Lago di Vico, 60 SCHIO (VI)
– tel. +39 0445 502011 – fax +39 0445 502010 - e-mail: [email protected]
E
N
G
L
I
S
H
8.2.4
SETTING THE DRUM PARAMETERS
Commands 71 to 80 :
This section allows the parameters relative to the physical configuration and some of the machine‟s
functioning modes to be modified. By entering one of these commands and pressing the
OK
pushbutton, the
message "
Compartment No. XX
" is displayed and shows the number of comparments set for the selected
drum. The values possible are: 4, 6, 8, 12, 16, 24, 48. Each time one of these values is changed, or the
setting is confirmed by pressing the ENTER pushbutton instead of pushbutton ESC, the drum is considered
empty and any products left in the compartments will not be accessible.
After pressing the ENTER pushbutton to store the number of compartments required or the ESC button if you
do not wish to store the value, the display shows the message "
Fifo/shopper X
" which enables the
functioning mode of that drum to be selected. If the value is
0
, the drum is set in shopper mode while; if the
value is 1, the drum is set in
Fifo
mode and the products will only be available for sale in the order in which
they were loaded. The preset value is usually set at
0
for
Shopper
mode.
The value can be confirmed with the ENTER pushbutton or, by pressing pushbutton ESC, the message
"
Expiry days YY
" displayed . YY indicates the shelf life of the products loaded in the selection starting from
the preceding midnight. This feature is only operative with the machine in
Intelligent reload
mode and the
sale of products that have not been sold within the programmed date is blocked.
For example, to programme drum no. 5 with 16 compartments in Shopper mode for products with a 7 day
expiry period, proceed as follows:
1.
Go into programming mode to display ..................................................................................
Command
00
2.
Key in
75
and press the ENTER button to display the no. of compartment .............
Compartment No. NN
3.
Key in
16
and press the
ENTER
button to display ..............................................................
Fifo/shopper X
4.
Key in
0
and press the
ENTER
button to display ..................................................................
Expiry days YY
5.
Key in
7
and press
ENTER
8.2.5
TO SET MACHINE PARAMETERS
Command 80 Cloning:
This command makes it possible to transfer all the parameters of the vending machine to a "Program Key",
to program same model machines. When you enter the command "Write Clone Key" appears on the display.
Then, enter the "Program Key" and press the ENTER key. "Data Writing…*" appears on the screen while the
data is being transferred to the key. Once the data transfer operation is completed, the machine returns to
the programming mode.
Caution: DO NOT enter the key before entering the programming mode, otherwise the vending machine will
fetch the data existing in the key.
Command 81 Fetch vend data:
This command makes it possible to transfer all the EVA-DTS data to a "Program Key". This data can be
extracted using special software (VMC configurator). The maximum number of possible registrations is 100.
Attention: if the key is not recognised as a data key, at the first registration the user will be asked to confirm
the complete deletion of the existing data.
Command 85 Display of checksum and main and power board software version.
Command 88 Enabling product heating on the WAVE MODULE
(if present)
:
This command enables operation of the microwave oven column. Value 1 = enabled; 0 = not enabled. If the
function is enabled, the system asks you to program the heating time, in seconds, for the products present on
each plate of the master machine (EASY 6000); value settable from 0 to 180 sec.
The heating times are calibrated for use with the maximum power output.
Содержание Easy 6000
Страница 1: ......