Western LOW-PRO 300W Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 106

background image

Lit. No. 72131, Rev. 00

July 15, 2018

39

STEEL HOPPER SPREADERS – TESTING

Checking Vehicle Spreader Harness

1. Disconnect the vehicle spreader harness from

the vehicle control harness at the black 6-pin
connector. Disconnect the vehicle spreader
harness from the 8-pin spreader harness at
the rear of the vehicle. Leave the POSITIVE (+)
and NEGATIVE (

–)

battery leads connected to

the battery.

2. Visually inspect the wiring harness for damage.

3. At the 8-pin connector, check for continuity

between all pins 3

–8.

T

here should NOT be

continuity between any combinations of
these wires.

4. Take the jumper wire and connect it between

pins 2 and 3 of the black 6-pin connector. Now
connect the meter between pins 6 and 7 of the
black 8-pin plug.

The meter should read zero

resistance.

NOTE: If the harness fails any of the above
tests, replace the harness.

5. With a meter, check for battery voltage at

pins 1 and 2 of the 8-pin plug. If the voltage is
low, or if no power exists, check for loose or
corroded connections at the vehicle battery
and at the 100A mega fuse.

6. With the positive lead of the meter connected

to pin 1 of the black 8-pin plug, take the black
lead and check pin 8 of this plug for battery
voltage. Also check pin 1 of the black 6-pin
connector for battery voltage.

7. Take the jumper wire and connect it between

pins 1 and 3 of the 8-pin plug. Now at the black
6-pin connector, check for battery voltage.
Connect the red lead of the tester to pin 5 and
the black tester lead to pin 1.

8. To check the license plate light, turn on the

parking lights, and check for battery voltage at
pin 4.

9. If the orange (Center High Mounted Stop Light)

CHMSL wire is connected to the brake lighting
circuit at the rear of the vehicle, depress the
brake pedal and check for battery voltage at
pin 5 of the black 8-pin plug.

NOTE: Not all vehicles will connect at the rear
of the vehicle. Some may need to be connected
in the cab. Check the body builder's guide
pertaining to the make of the vehicle.

«
...
39
40
41
42
43
...
»

Содержание LOW-PRO 300W











































































































Отзывы:

Нет отзывов

Похожие инструкции для LOW-PRO 300W

Perfect Binder D1

Бренд: Canon Страницы: 99

SmartPOS PAX A80

Бренд: Handpoint Страницы: 6

Бренд: Baltech Страницы: 5

Бренд: Hi-Spec Страницы: 27

Бренд: NEC Страницы: 15

Бренд: The Andersons Страницы: 8

Бренд: Satel Страницы: 2

Бренд: The Handy Страницы: 20

Бренд: The Handy Страницы: 21

Бренд: The Handy Страницы: 24

Single-Slot Card Readers

Бренд: Edge Страницы: 1

Бренд: WilTec Страницы: 8

Бренд: IDTECK Страницы: 17

TWN4 PALON COMPACT LEGIC M

Бренд: Elatec Страницы: 14

Бренд: IDTECK Страницы: 24

Бренд: LEHNER Страницы: 45

Бренд: JARLTECH Страницы: 24

Бренд: Hama Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды