background image

Lit. No. 72131, Rev. 00 

   

July 15, 2018

21

POLY HOPPER SPREADERS – CONTROLLING MATERIAL APPLICATION

The material application settings can be adjusted 
while spreader is ON or OFF. Settings are shown 
by the indicator lights around the control knobs. 
When the spreader is OFF, a single LED will light 
to show the current setting. When the spreader 
is ON, the number of blue LEDs illuminated 
will increase/decrease as the knobs are turned 
clockwise/counterclockwise.

The hopper drive will not deliver material until the 
ON button is pressed.

The Material Width (left) knob controls spinner 
speed. Turning the knob clockwise will increase 
the width of the application area.

The Material Flow (right) knob controls the hopper 
drive. Turning the knob clockwise will increase the 
feed rate of material to the spinner.

Turning the control knobs counterclockwise will 
decrease the width of the application area and the 
feed rate of material.

BLAST/Maximum Application

1.  Press and hold the BLAST button when 

maximum 

fl

 ow rate and application area are 

needed temporarily. The BLAST button will 
illuminate while depressed.

2.  Release the button when maximum application 

settings are no longer needed.

NOTE: Spinner speed and material feed rate 
revert to the previous settings once the BLAST 
button is released.

CAB CONTROL MODES

Standby Mode

Vehicle ignition is set to ACC or ON; cab control 
is OFF. Control has power. No spreader was 
detected. No lights are illuminated on the control. 
Press any button to wake.

Ready Mode

Vehicle ignition is set to ACC or ON; cab control is 
OFF. Control has power. Spreader is detected.

The Material Width and Material Flow control 
knobs can be set to start-up conditions, but the 
spinner and drives will not operate until the cab 
control is turned ON. 

Accessory lights and vibrator (if installed) are 
operational. The BLAST function is not operational. 

ON Mode

Vehicle ignition is set to ACC or ON; cab control is 
ON.

Spinner and hopper motors will start. All cab 
control functions are operational. Accessory lights 
and vibrator (if installed) are operational.

During normal spreader operation, 

no control 

codes are displayed

. Information or setup codes 

will appear when relevant. These codes will not 
stop spreader operation.

Error Mode

When an error condition occurs, spreader 
operation will shut down. A two-digit error code will 

fl

 ash on the display and a beep will sound. If there 

are multiple error codes, the codes will 

fl

 ash in a 

repeating sequence. 

Refer to the Error Codes beginning on page 14 
of the Cab Control Codes table. Also see the 
Troubleshooting Guide section of this manual.

Once the error condition has been resolved, press 
the ON/OFF button to clear the error code(s). 
Press the ON/OFF button again to resume 
spreader operation.

The error code will reappear if the error condition 
has not been recti

fi

 ed. If the error condition 

persists, contact your authorized dealer.

Multiple resets within a short time frame will cause 
the hopper module to time out if components are 
overheating. The control will display an 

EF

 error 

code.

Accessory work lights and strobe lights can be 
used when an error code is in effect and will 
remain in their current state. The vibrator and 
pre-wet will not function.

Содержание LOW-PRO 300W











































































































Отзывы: