Western LOW-PRO 300W Скачать руководство пользователя страница 92

Страница: 92 / 106

Lit. No. 72131, Rev. 00

July 15, 2018

TAILGATE SPREADERS: TROUBLESHOOTING GUIDE

Problem

Possible Cause

Suggested Solution

Motor does not run.

Unplug the spreader harness and tag out, if required, before performing any of the following repairs.

1. Electrical connections are loose.

1. Open access cover and check motor, harness, and module

connections.

2. Blown fuse.

2. Replace spreader vehicle battery cable fuse.

3. Motor seizes.

3. Replace motor.

Material does not

ow.

Unplug the spreader harness and tag out, if required, before performing any of the following repairs.

1. Obstruction in hopper.

1. Clear obstruction.

2. Material bridged.

2. Clear the bridged material or adjust the baf

e extension.

3. Auger loose on shaft.

3. Align auger with

at machined area on shaft and tighten

locking bolt on side of auger.

4. Auger runs backward.

4a. Check the wire connections at the "P—FEED—N" posts on

the spreader module. Auger harness RED to P—FEED; auger
harness BLACK to FEED—N.

4b. Check that auger motor harness is correct part number for

spreader model.

5. Material is wet.

5. Replace with dry material.

6. Material is coarse or frozen.

6. Replace material.

7. Spinner does not turn.

7. Check connection inside motor enclosure.

Material free

ows.

1. Incorrect baf

e length.

1a. Install correct baf

1b. Adjust the baf

e extension.

2. Baf

e does not touch hopper on three sides.

2. Reposition baf

Vibrator does not work.

1. Electrical connections are loose.

1a. Check the vibrator to harness connection.
1b. Check vibrator harness to module connections (BAT, GND, and

blue bullet connector).

2. Blown fuse.

2. Open access cover to replace fuse in the fuse holder on the

vibrator harness.

3. Vibrator failure.

3. Replace vibrator.

TAILGATE SPREADERS Troubleshooting

(continued)

Содержание LOW-PRO 300W











































































































Результаты поиска

Содержание LOW-PRO 300W

Отзывы:

Похожие инструкции для LOW-PRO 300W

Бренды по названию

Популярные бренды

Western LOW-PRO 300W, Руководство механика

Результаты поиска

Содержание LOW-PRO 300W

Отзывы:

Похожие инструкции для LOW-PRO 300W

Бренды по названию

Популярные бренды