Western LOW-PRO 300W Скачать руководство пользователя страница 58

Страница: 58 / 106

Lit. No. 72131, Rev. 00

July 15, 2018

6. Tighten the tensioner adjustment bolt jam nut.

7. Check the chain tension. Correct tension

allows the chain to move 1/4" when pressed
midway between the sprockets. To adjust the
tension, repeat Steps 2–6 as required.

8. Tighten the tensioner pivot bolt nut to 30 ft-lb.

Tighten the tensioner adjustment bolt jam nut.

9. Hook the rubber latch into the latch keeper on

the tensioner lever.

10. Close the engine cover and secure the back

latches. Close and latch the access door.

Excerpts taken from Striker™ Steel Hopper Spreader Installation Instructions (Lit. No. 99587/99593, Rev. 02).

STEEL HOPPER SPREADERS – GAS – ELECTRIC CLUTCH

Installing Electric Clutch (cont.)

10. Install the #40 chain from the engine sprocket to

the clutch sprocket by loosening the four bolts
that hold the engine base. Slide it toward the
clutch assembly. Install the chain and slide the
base away from the clutch to tighten the chain.

11. Do NOT overtighten the chain. There should

be 1/4" de

ection midway between the

sprockets. Tighten the four engine base bolts.

12. Install the 16-tooth sprocket that runs the

spinner. Tighten both set screws.

13. Using a straight edge, check the alignment of

the spinner shaft and spinner drive sprockets.

14. To adjust sprocket alignment, loosen the spinner

sprocket set screw, adjust the sprocket position up
or down as required, and retighten the set screw.

15. Install the drive chain over the spinner shaft

and spinner drive sprockets.

Adjust Spinner Drive Chain Tension

1. Position the tensioner so it is fully extended,

with the idler sprocket engaged with the chute
drive chain.

2. Loosen the pivot bolt and nut.

3. Slide the tensioner toward the chain until the

chain is tight.

4. Tighten the tensioner pivot bolt nut.

5. Loosen the tensioner adjustment bolt jam

nut and advance the adjustment bolt until it
contacts the tensioner pivot bolt nut. This will
keep the pivot bolt from moving.

(Chain not
shown.)

Chain Tensioner

Lever

Level sprockets.

1/4"

Deflection

Check alignment
of sprockets.

Rubber

Latch

Tensioner

Adjustment

Bolt

Jam Nut

Latch

Keeper

(Rubber latch not shown.)

Tensioner
Pivot Bolt

Pivot Bolt

Nut

Содержание LOW-PRO 300W











































































































Результаты поиска

Содержание LOW-PRO 300W

Отзывы:

Похожие инструкции для LOW-PRO 300W

Бренды по названию

Популярные бренды

Western LOW-PRO 300W, Руководство механика

Результаты поиска

Содержание LOW-PRO 300W

Отзывы:

Похожие инструкции для LOW-PRO 300W

Бренды по названию

Популярные бренды