Wellsys W9CT Скачать руководство пользователя страница 13

To Flush the TCR filter

1. The TCR filter must be flushed backwards.
2. Switch water lines, so that the blue drain line is in the input side of the sediment head and the

black water supply line is in the out put side of the pre carbon filter head.

3. Remove the sediment filter and connect it to the pre carbon head.
4. Remove the TCR filter and connect it to the sediment filter head. Please see arrangement in the

picture below.

5. Turn the water on and flush for 3 minutes.
6. After turning the water off you may put the tubing and all filters back to the previously installed

locations.

Flushing the RO membrane for 30 minutes: 

1. It is important to flush the RO membrane with all filters inline for a full 30 minutes.  Although

the RO membrane will flush down to 98% reduction in TDS within 5-10 minutes, the remaining
20 minutes is necessary to completely flush the preservative out of the membrane and to flush
the higher TDS water out of the post filter.
a. Failure to complete this test, especially when using the “Boost” filter will result in poor

taste and may cause further damage to the equipment.

2. Connect the source line to the back of the system in the “tap water” bulkhead fitting.
3. Connect a drain line into the “RO drain” bulkhead fitting

a. This is represented with the blue tubing .

4. Plug the power cord into active power.

13

13

Содержание W9CT





































Отзывы: