background image

Page 8

990008 Rev. H

AND OTHER SPECIFIED HAZARDS ONLY

IN ACCORDANCE WITH CAN/CSA C22.2 NO. 601.1

21ZJ

2. Safety

The Kreativ Mach 5.0 and Mach 5.0 PLUS systems are designed  for use only by and
on the order of a dentist.

Warnings

Always wear protective eye equipment in order to avoid corneal abrasion or irritation if
particles are deflected into the eye.  This applies to the dentist, staff, and patient.

A rubber dam is recommended

 

in order to avoid injury to gingiva or other soft tissue,

and for interproximal preparations to protect adjacent tooth surfaces.

Never direct the  handpiece to an open pulp chamber or at  pulpal exposures.  Also
never place the  handpiece in direct contact with the  gingiva when the air pressure is
activated.  While the abrasive stream will not cut the gingival tissue, it may irritate it.

All Kreativ Mach 5.0 and Mach 5.0 PLUS accessories which come into contact with
the patient should be sterilized prior to each use.  Always disinfect the handpiece cradle
in the remote control unit before each patient use.

Always use your high volume evacuation system when using the  handpiece of the
Kreativ Mach 5.0 or Mach 5.0 PLUS

.

  Have the dental assistant place the high volume

evacuation system in close proximity to the operative site.

Make sure that the Kreativ Mach 5.0 and Mach 5.0 PLUS systems are connected to a
properly grounded electrical outlet.

Always replace fuses with fuses of the proper rating, as indicated in the Chapter 1.

Cautions

For dental cleaning (prophylaxis) procedures, be absolutely sure that the
chamber and hose have been completely cleared of all abrasive powders and use
only bicarbonate in the chamber

.

Chapter

2

Содержание Kreativ Mach 5.0






































Отзывы: