Welbilt Koolaire KD0270A Скачать руководство пользователя страница 71

Страница: 71 / 136

Discharge Pressure High Checklist

Improper Installation

• Refer to “Installation and Visual Inspection Checklist”

Restricted Condenser Air Flow

•  High inlet air temperature
•  Condenser discharge air re-circulation
•  Dirty condenser fins
•  Defective fan cycling control
•  Defective fan motor

Improper Refrigerant Charge

•  Overcharged
•  Non-condensible in system
•  Wrong type of refrigerant

Other

•  Non-OEM components in system
•  High side refrigerant lines/component
•  Restricted (before mid-condenser)

Freeze Cycle Discharge Pressure Low Checklist

Improper Installation

• Refer to “Installation and Visual Inspection Checklist”

on page 59.

Improper Refrigerant Charge

• Undercharged
• Wrong type of refrigerant

Other

• Non-OEM components in system
• High side refrigerant lines/component restricted

(before mid-condenser)

• Defective fan cycle control
NOTE: Do not limit your diagnosis to only the items listed

in the checklists.

Содержание Koolaire KD0270A









































































































































Результаты поиска

Содержание Koolaire KD0270A

Отзывы:

Welbilt Koolaire KD0270A, Руководство техника, Страница: 71 / 136

Результаты поиска

Содержание Koolaire KD0270A

Отзывы: