Welbilt Koolaire KD0270A Скачать руководство пользователя страница 63

Страница: 63 / 136

Part Number STH047 Rev01 10/18 63

SAFETY LIMIT FEATURE

In addition to the standard safety controls, your Koolaire®

ice machine features built-in safety limits that will stop the

ice machine if conditions arise which could cause a major

component failure.
Before calling for service, re-start the ice machine using

the following procedure:

1. Move the ON/OFF/WASH switch to OFF and then back

to ON.

2. If the safety limit feature has stopped the ice

machine, it will restart after a short delay. Proceed to

step 4.

3. If the ice machine does not restart, see “Ice machine

does not operate”.

4. Allow the ice machine to run to determine if the

condition is reoccurring.
A. If the ice machine stops again, the condition has

reoccurred. Call for service.

B. If the ice machine continues to run, the condition

has corrected itself. Allow the ice machine to

continue running.

Содержание Koolaire KD0270A









































































































































Результаты поиска

Содержание Koolaire KD0270A

Отзывы:

Welbilt Koolaire KD0270A, Руководство техника, Страница: 63 / 136

Результаты поиска

Содержание Koolaire KD0270A

Отзывы: