Welbilt Koolaire KD0270A Скачать руководство пользователя страница 55

Страница: 55 / 136

Part Number STH047 Rev01 10/18 55

Step 3

Disconnect the ice thickness probe from

the control board terminal. Clip the jumper wire to the

terminal on the control board and any cabinet ground.

Monitor the harvest light.

EVAPORATOR

ICE THICKNESS

PROBE

CONNECTION

GROUND

JUMPER WIRE

BIN SWITCH

LIGHT

(GREEN)

HARVEST LIGHT

(RED)

SV1592J

Step 3 Jumper wire connected from control board terminal to

ground

Monitoring Harvest Light

Correction

The harvest light comes on, and

6-10 seconds later, ice machine

cycles from freeze to harvest.

The ice thickness probe is

causing the malfunction.

The harvest light comes on but

the ice machine stays in the

freeze sequence.

The control circuitry is

functioning properly. The ice

machine is in a six-minute

freeze time lock-in (verify step 1

of this procedure was followed

correctly).

The harvest light does not

come on.

The control board is causing the

malfunction.

Содержание Koolaire KD0270A









































































































































Результаты поиска

Содержание Koolaire KD0270A

Отзывы:

Welbilt Koolaire KD0270A, Руководство техника, Страница: 55 / 136

Результаты поиска

Содержание Koolaire KD0270A

Отзывы: