Welbilt Koolaire KD0270A Скачать руководство пользователя страница 54

Страница: 54 / 136

Part Number STH047 Rev01 10/18

DIAGNOSING ICE THICKNESS CONTROL CIRCUITRY
Ice Machine Does Not Cycle Into Harvest when Water

Contacts the Ice Thickness Control Probe

Step 1

Bypass the freeze time lock-in feature by

moving the ON/OFF/WASH switch to OFF and back to ON.

Wait until the water starts to flow over the evaporator.

Step 2

Clip the jumper wire to the ice thickness probe

and any cabinet ground.

EVAPORATOR

ICE THICKNESS

PROBE

CONNECTION

GROUND

JUMPER WIRE

BIN SWITCH

LIGHT

(GREEN)

HARVEST LIGHT

(RED)

SV1592i

Step 2 Jumper wire connected from probe to ground

Monitoring Harvest Light

Correction

The harvest light comes on, and

6-10 seconds later, ice machine

cycles from freeze to harvest.

The ice thickness control

circuitry is functioning properly.

Do not change any parts.

The harvest light comes on but

the ice machine stays in the

freeze sequence.

The ice control circuitry is

functioning properly. The ice

machine is in a six minute

freeze time lock-in. Verify

Step 1 of this procedure was

followed correctly.

The harvest light does not

come on.

Proceed to Step 3.

Содержание Koolaire KD0270A









































































































































Результаты поиска

Содержание Koolaire KD0270A

Отзывы:

Welbilt Koolaire KD0270A, Руководство техника, Страница: 54 / 136

Результаты поиска

Содержание Koolaire KD0270A

Отзывы: