Welbilt Koolaire KD0270A Скачать руководство пользователя страница 24

Страница: 24 / 136

Part Number STH047 Rev01 10/18

COOLING TOWER APPLICATIONS
Water Cooled Models Only

A water-cooling tower installation does not require

modification of the ice machine. The water regulator valve

for the condenser continues to control the refrigeration

discharge pressure.
It is necessary to know the amount of heat rejected, and

the pressure drop through the condenser and water valves

(inlet to outlet) when using a cooling tower on an ice

machine.
• Water entering the condenser must not exceed 90°F

(32.2°C).

• Water flow through the condenser must not exceed 5

gallons (19 liters) per minute.

• Allow for a pressure drop of 7 psig (.48 bar) between

the condenser water inlet and the outlet of the ice

machine.

• Water exiting the condenser must not exceed 110°F

(43.3°C).

Caution

Plumbing must conform to state and local codes.

Содержание Koolaire KD0270A









































































































































Результаты поиска

Содержание Koolaire KD0270A

Отзывы:

Welbilt Koolaire KD0270A, Руководство техника, Страница: 24 / 136

Результаты поиска

Содержание Koolaire KD0270A

Отзывы: