Welbilt Koolaire KD0270A Скачать руководство пользователя страница 27

Страница: 27 / 136

Part Number STH047 Rev01 10/18 27

ICE MACHINE INSPECTION

Check all water fittings and lines for leaks. Also, make sure

the refrigeration tubing is not rubbing or vibrating against

other tubing, panels, etc.
Do not put anything (boxes, etc.) in front of the ice

machine. There must be adequate airflow through and

around the ice machine to maximize ice production and

ensure long component life.

EXTERIOR CLEANING

Clean the area around the ice machine as often as

necessary to maintain cleanliness and efficient operation.
Sponge any dust and dirt off the outside of the ice machine

with mild soap and water. Wipe dry with a clean, soft

cloth.
A commercial grade stainless steel cleaner/polish can be

used as necessary.

CLEANING THE CONDENSER

Warning

Disconnect electric power to the ice machine at the

electric service switch before cleaning the condenser.

Caution

If you are cleaning the condenser fan blades with

water, cover the fan motor to prevent water damage.

FIN COMB

CONDENSER

COMB

DOWN

ONLY

Maintenance

Содержание Koolaire KD0270A









































































































































Результаты поиска

Содержание Koolaire KD0270A

Отзывы:

Welbilt Koolaire KD0270A, Руководство техника, Страница: 27 / 136

Результаты поиска

Содержание Koolaire KD0270A

Отзывы: