Weinmann MEDUMAT Easy CPR Скачать руководство пользователя страница 51

Страница: 51 / 60

Tools and Test Equipment

8.3 Testing equipment

• Oxygen concentration meter, type Oxycontrol WM 13550

• Volume flow meter

Typ Flow Analyser PF-300

obtainable from:
imtmedical ag
Gewerbestraße 8
CH-9470 Buchs
Tel.: + 41 81 750 66 99
Fax: + 41 81 750 66

www.imtmedical.com

Type RT 200 (Timeter)

obtainable from:
Allied Healthcare Products Inc.
1720 Sublette Avenue
St. Louis, Missouri, MO 63110
USA
Tel.: 001-800-444-3954
Fax: 001-314-771-5183

Type EKU VIP ventilator tester

obtainable from:
EKU Elektronik GmbH
Feldstraße 9a
D-56291 Leiningen
Tel.: 0049 6746-1018
Fax: 0049 6746-8484
www.eku-elektronik.de

• Test set for final check

WM 15357

• Set, supply test

Medumat/Modules

WM 15440

• Set, test set ventilation and pressure reducer

flow

WM 15443

• Pressure gauge 0 to 6.3 bar, class 1.6;

• Pressure gauge 0 – 100 mbar, class 1.6

Type WIKA

obtainable from:
Alexander Wiegand GmbH & Co.
Alexander-Wiegand-Strasse 30
D-63911 Klingenberg am Main
Germany
Tel.: 0049 9372/1320

• Digital multimeter

• Hazet torque wrench

obtainable from:

Hommel
Heidelberger Str. 52
D-68519 Viernheim
Germany
Tel.: 00 49 6204/738-0
Fax: 00 49 6204/739-222

Содержание MEDUMAT Easy CPR





























































Результаты поиска

Содержание MEDUMAT Easy CPR

Отзывы:

Бренды по названию

Популярные бренды

Weinmann MEDUMAT Easy CPR, Инструкции по обслуживанию и ремонту

Результаты поиска

Содержание MEDUMAT Easy CPR

Отзывы:

Бренды по названию

Популярные бренды