Weil-McLain CGt 2 Series Скачать руководство пользователя | Manualshive

Страница: 9 / 68

background image

9

Part Number

550-110-290/0219

CGt

GAS-FIRED WATER BOILER — Series 2 —

Boiler Manual

Prepare boiler location — contamination

1e

Table 1

Corrosive or destructive contaminants and likely locations

To prevent potential of severe personal injury or death, check for products or areas listed
below before installing boiler. If any of these contaminants are found:
• remove contaminants permanently

— OR —

• isolate boiler and provide outside combustion air. See national, provincial or local codes

for further information.

Please review the following information on potential
combustion air contamination problems.

Refer to

Table 1

for products and areas which may cause

contaminated combustion air.

CONSTRUCTION DUST HAZARD

— Airborne particulates, such as drywall dust

or fiberglass dust, will cause blockage of the CGt burners, resulting in carbon monoxide
production, a fire hazard, or building freeze damage. If the boiler is operated during con-
struction, you must isolate the boiler to provide clean air for combustion.

If you are unable

to ensure uncontaminated air in the boiler vicinity at all times, you must inspect the
boiler at least once weekly

. When inspecting, clean the burners if necessary using the

procedure given on page 41. Failure to follow these guidelines could result in severe personal
injury, death or substantial property damage.

Products to avoid

Areas likely to have contaminants

Spray cans containing chloro/fluorocarbons

Dry cleaning/laundry areas and establishments

Permanent wave solutions

Swimming pools

Chlorinated waxes/cleaners

Metal fabrication plants

Chlorine-based swimming pool chemicals

Beauty shops

Calcium chloride used for thawing

Refrigeration repair shops

Sodium chloride used for water softening

Photo processing plants

Refrigerant leaks

Auto body shops

Paint or varnish removers

Plastic manufacturing plants

Hydrochloric acid/muriatic acid

Furniture refinishing areas and establishments

Cements and glues

New building construction

Antistatic fabric softeners used in clothes dryers

Remodeling areas

Chlorine-type bleaches, detergents, and cleaning
solvents found in household laundry rooms

Garages with workshops

Adhesives used to fasten building products and
other similar products

Buildings under construction (where air is
contaminated with particulates)

Airborne particulates (drywall dust, fiberglass
particles, road or gravel dust, lint, etc.)

«
...
7
8
9
10
11
...
»

Содержание CGt 2 Series





































































Отзывы:

Нет отзывов

Похожие инструкции для CGt 2 Series

Бренд: IBC Страницы: 104

Бренд: Magikitch'n Страницы: 18

Mexico Super RS 3/60P

Бренд: IDEAL Страницы: 8

Бренд: Hamworthy Страницы: 28

Бренд: iQe Страницы: 48

Aerco Benchmark 5000

Бренд: Watts Страницы: 76

Бренд: Beretta Страницы: 48

Бренд: NTI Страницы: 4

Бренд: Monzana Страницы: 7

Logano plus GB102

Бренд: Buderus Страницы: 12

Бренд: Baxi Страницы: 20

Бренд: Viessmann Страницы: 4

Бренд: Viessmann Страницы: 36

EVO-COOL CS 1300

Бренд: Viessmann Страницы: 36

ecoTEC pure VC 146/7-2

Бренд: Vaillant Страницы: 20

Ultra-Max Lava Rock Gas Char-Broilers 8024CB

Бренд: Star Manufacturing Страницы: 2

Star-Max Lava Rock Gas Char-Broilers 6015CBD

Бренд: Star Manufacturing Страницы: 2

Бренд: Star Manufacturing Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды