Weil-McLain CGt 2 Series Скачать руководство пользователя

Страница: 17 / 68

Venting — direct exhaust — termination

Part Number

550-110-290/0219

CGt

GAS-FIRED WATER BOILER — Series 2 —

Boiler Manual

Figure 12 Vent termination

minimum clearances

1. Locate the boiler and vent penetration through the

wall so all requirements on this page and in

Figure

12 will be met. Also follow vent manufacturer’s

instructions.

2. Gases will form white plume in winter. Plume could

obstruct window view.

3. Prevailing winds could cause freezing of condensate

and water/ice buildup on vent termination, building,

plants or roof. Ice buildup on vent termination can

cause boiler shutdown and building freezeup.

4. Winds over 40 mph can cause nuisance boiler shut-

down if boiler is sidewall vented. This could result

in loss of heat to building, causing freezeup.

5. Locate or guard vent termination to prevent con-

densate from damaging exterior surfaces.

6. Locate the vent termination well away from trees,

shrubs, and decorative items.

7. Locate or guard vent to prevent accidental contact

by people or pets.

8. Do not terminate vent in window well, stairwell,

alcove, courtyard, or other recessed areas.

9. Do not wrap or insulate vent pipe or fittings.
10. Do not terminate vent above any door or window.

Condensate can freeze, causing ice formations.

11. Do not connect:

• Any other appliance to vent pipe.
• Multiple boilers to a common vent pipe.

12. Canadian installations — See B149.1 or B149.2

Installation Code. Terminate vent no less than 6

feet from another combustion air inlet, 3 feet from

any other building opening, and 3 feet from any gas

service regulator.

13. See

Figure

, showing that the vent must terminate:

• more than 4 feet below or to side of all doors

or windows.

• more than 1 foot above grade or anticipated

snow line.

• at least 7 feet above public walkway.
• 3 feet above any forced air intake within 10

feet.

14. Vent must also terminate:

•  at least 6 feet away from adjacent walls.
•  no closer than 5 feet below roof overhang.
•  at least 4 feet horizontally (and in no case

above or below unless a 4 foot horizontal

distance is maintained) from electric meters,

gas meters, regulators, relief valves, and other

equipment.

15. Site conditions may dictate greater clearances.
16. Do not extend exposed vent pipe outside of building.

Condensate could freeze and block vent pipe.

A gas vent extending through an

exterior wall shall not terminate ad-
jacent to the wall or below building
extensions such as eaves, parapets,
balconies or decks. Failure to comply
could result in severe personal injury,
death or substantial property damage.

Follow instructions on this page when determining vent

location to avoid possibility of severe personal injury,

death or substantial property damage.

Содержание CGt 2 Series





































































Результаты поиска

Содержание CGt 2 Series

Отзывы:

Похожие инструкции для CGt 2 Series

Бренды по названию

Популярные бренды

Weil-McLain CGt 2 Series, Руководство пользователя

Результаты поиска

Содержание CGt 2 Series

Отзывы:

Похожие инструкции для CGt 2 Series

Бренды по названию

Популярные бренды