Weil-McLain CGt 2 Series Скачать руководство пользователя

Страница: 52 / 68

Part Number

550-110-290/0219

CGt

GAS-FIRED WATER BOILER — Series 2 —

Boiler Manual

Troubleshooting — control module lights

(cont.)

12c

CHART 4 –– FLAME & POWER light flashing

–– Usually indicates flame sensed when it shouldn’t be there ––

120

Electrical shock hazard

— Wherever you see ▲

TURN OFF POWER

▲, follow the instructions. Failure to follow

instructions could result in severe personal injury, death or substantial property damage.

•

▲

TURN OFF POWER

▲

to boiler at service switch

or breaker.

• Open main manual gas

valve.

• Turn on power to boiler

at service switch or

breaker.

• Restart boiler per operating

instructions.

• Perform start-up

procedures in boiler

manual to verify proper

operation.

• Boiler may now be

operating

normally.

• Perform start-up

procedures in

boiler manual to

verify proper

operation.

• Replace control module.
• Retest.

Are manual main shutoff valve and gas valve open?

Yes

• Replace gas valve.
• Retest boiler.

Are

FLAME

POWER

lights flashing?

Yes

• Replace control

module.

• Retest.

• Boiler should now

operate normally.

• Original flashing

FLAME

light

caused by gas

valve not

operating properly.

• See normal

sequence of

operation,

Figure 27,

page 34

•  Turn off power to the boiler at service switch or breaker.
•  Wait at least 45 seconds.
•  Turn on power to boiler.
•  Restart boiler, following

Operating instructions

in this

manual (Section

c).

• Look through the pilot inspection port to see if the pilot

is burning during the prepurge period (first 30 seconds

of operation).

Is pilot burning during prepurge period?

Yes

• Replace control

module.

• Retest.

•  Leave main manual gas valve closed.
•  Turn off power to boiler at service switch or breaker.
•  Wait at least 45 seconds.
•  Turn on power to boiler.
•  Restart boiler, following

Operating instructions

in this

manual (Section

c).

FLAME

and

POWER

lights still flash?

Yes

• Allow boiler to continue cycling.

Are

FLAME

POWER

lights flashing?

Yes

Содержание CGt 2 Series





































































Результаты поиска

Содержание CGt 2 Series

Отзывы:

Похожие инструкции для CGt 2 Series

Бренды по названию

Популярные бренды

Weil-McLain CGt 2 Series, Руководство пользователя

Результаты поиска

Содержание CGt 2 Series

Отзывы:

Похожие инструкции для CGt 2 Series

Бренды по названию

Популярные бренды