Weil-McLain CGt 2 Series Скачать руководство пользователя | Manualshive

Страница: 18 / 68

background image

Venting – direct exhaust – vertical or sidewall

3f

Condensate drain line — use only silicone tubing
rated for at least 400°F for the condensate drain
line. Using any other material could cause flue gas
leakage, potentially resulting in severe personal
injury, death or substantial property damage.

On some installations, the condensate drain fitting
may be omitted, provided:
• Vent manufacturer shows this option in their

instructions.

• Vent is sloped toward termination as shown in

dotted lines in Figure 14.

• The vent is installed per Weil-McLain and vent

manufacturer’s instructions.

Condensate drippage from such vents may accu-
mulate on the ground below. Consider traffic in
the area to avoid hazard due to ice accumulation.
Ice buildup may also block vent.

18

Part Number

550-110-290/0219

CGt

GAS-FIRED WATER BOILER — Series 2 —

Boiler Manual

Figure 13 Direct exhaust

vertical venting

Figure 14 Direct exhaust

sidewall venting

1. Do not mix types or manufacturers of vent materials.
2. Clean all joints before sealing. See vent manufacturer’s instructions

for cleaning and sealing joints. Use their specified sealant. Do not use

screws.

3. Install vent pipe with seams on top of vent horizontal runs. Follow

requirements in Section 3e, page 17, for vent termination.

4. Maintain minimum 2” clearance from combustible materials to vent

pipe.

5.

Vertical venting

— See Figure 13. Follow vent manufacturer’s in-

structions for venting through roof.
• Vent pipe must extend through roof flashing, jacket or thimble.
• Vent may pass through floor, inside wall or concealed space

when installed according to vent manufacturer’s instructions.

Sidewall venting

— See Figures 14 and 15. Vent must termi-

nate at least one foot above anticipated snowline. Vent must be

terminated only with:

• Tee or elbow with integral screen. Tee must be mounted verti-

cally.

• Elbow and termination coupling with screen (not available for

StaR-34).

6. Do not seal vent pipe (slip connector for Saf-T Vent) to inside or

outside plate.

7. If passing through noncombustible wall, provide hole diameter large

enough to insert the vent pipe (slip connector for Saf-T Vent).

8. Install horizontal drain tee as close as possible to boiler, in first hori-

zontal run. See Figure 13.

9. Do not exceed the maximum vent system length given in Table 4,

page 15.

«
...
16
17
18
19
20
...
»

Содержание CGt 2 Series





































































Отзывы:

Нет отзывов

Похожие инструкции для CGt 2 Series

Бренд: A.O. Smith Страницы: 68

Mexico Super FF440

Бренд: IDEAL Страницы: 4

Mexico Slimline CF3/40

Бренд: IDEAL Страницы: 40

Бренд: IDEAL Страницы: 4

Бренд: IDEAL Страницы: 4

Бренд: Raypak Страницы: 60

Henrad SE 30 FF

Бренд: Ideal Boilers Страницы: 4

Бренд: IDEAL Страницы: 6

Бренд: IDEAL Страницы: 4

Бренд: Main Страницы: 12

Бренд: Magikitch'n Страницы: 4

Бренд: Easylife Страницы: 4

Бренд: Steco Страницы: 28

Бренд: Viadrus Страницы: 48

Бренд: CleaverBrooks Страницы: 64

Бренд: Kiturami Страницы: 45

Бренд: Ariston Страницы: 8

NUVOLA DUO-TEC GA 16

Бренд: Baxi Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды