Weil-McLain CGt 2 Series Скачать руководство пользователя страница 33

Страница: 33 / 68

Part Number

550-110-290/0219

CGt

GAS-FIRED WATER BOILER — Series 2 —

Boiler Manual

Check-out procedure — checklist

❏

Boiler and heat distribution units filled with water?

❏

Automatic air vent, if used, open one full turn?

❏

Air purged from system?

❏

Air purged from gas piping? Piping checked for leaks?

❏

Correctly sized manifold orifices installed? Refer to page 12

to check size.

Correctly sized manifold orifices must be used.

Failure to do so will cause severe personal

injury, death or substantial property damage.

❏

Followed operating instructions on boiler or in manual Sec-

tion

for proper start-up?

❏

Proper burner flame observed? Refer to

Check burner flames

manual Section

❏

Test limit control — While burners are operating, move indi-

cator on limit control below actual boiler water temperature.

Burners should go off while circulator continues to operate.

Raise setting on limit control above boiler water temperature

and burners should reignite.

❏

Test tankless heat low limit control — While burners are

operating, move indicator on low limit control above actual

boiler water temperature. The 3-way valve should operate to

bypass all flow around the boiler. If low limit and valve operate

correctly, turn setting on low limit back to normal. The 3-way

valve should return to normal position.

❏

Test additional field-installed controls — If boiler has a low

water cutoff, additional high limit or other controls, test for

operation as outlined by manufacturer. Burners should be

operating and should go off when controls are tested. When

controls are restored, burners should reignite. Test ambient

temperature switch by disconnecting one of the wires from

the switch. Boiler shut down until wire is replaced.

❏

Test ignition system safety device:
a. Connect manometer to outlet side of gas valve.
b. Start boiler, allowing for normal start-up cycle to occur

and main burners to ignite.

c. With main burners on, manually shut off gas supply at

manual main shutoff gas valve. Burners should go off.

d. Open manual main shutoff gas valve. Manometer

should confirm there is no gas flow.

e. Pilot will relight, flame sensing element will sense pilot

flame and main burners will reignite.

❏

Set limit control(s) to system temperature requirements.

Adjust balancing valves and controls to provide design tem-

perature to system.

❏

For multiple zones, adjust flow so it is about the same in each

zone.

❏

Verify thermostat heat anticipator (if available) set properly?

Refer to

Field wiring

, manual Section

, page 29,

Thermostat

❏

Cycle boiler with thermostat — Raise to highest setting and

verify boiler goes through normal start-up cycle. Lower to

lowest setting and verify boiler goes off.

❏

Measure natural gas input:
a.  Operate boiler 10 minutes.
b.  Turn off other appliances.
c.  At natural gas meter, measure time (in seconds) re-

quired to use one cubic foot of gas.

d. Calculate gas input:

3600 x 1000

number of seconds from step

= Btuh

e. Btuh calculated should approximate input rating on

boiler rating label.

❏

Check manifold gas pressure by connecting manometer to

downstream test tapping on main gas valve. Manifold pressure

for natural gas should be 3.5" w.c.

❏

Observe several operating cycles for proper operation.

❏

Set room thermostat to desired room temperature.

❏

Fill in Installation and service certificate below?

❏

Review all instructions shipped with this boiler with owner

or maintenance person. Return instructions to envelope and

give to owner or place in pocket inside front panel in boiler.

Installation and service certificate

Boiler model __________________ Series __________ CP number ___________ Date installed ___________

Measured Btuh input ____________________

Installer ________________________ ________________________________ ________________________
(company) (address) (phone)

Installer’s signature: _____________________________________

Installation and service certificate

Содержание CGt 2 Series





































































Результаты поиска

Содержание CGt 2 Series

Отзывы:

Похожие инструкции для CGt 2 Series

Бренды по названию

Популярные бренды

Weil-McLain CGt 2 Series, Руководство пользователя

Результаты поиска

Содержание CGt 2 Series

Отзывы:

Похожие инструкции для CGt 2 Series

Бренды по названию

Популярные бренды