Weil-McLain CGt 2 Series Скачать руководство пользователя

Страница: 39 / 68

Table 8

Service and maintenance schedules

Follow the

Service and maintenance

procedures given throughout this manual and in com-

ponent literature shipped with the boiler. Failure to perform the service and maintenance

could result in damage to the boiler or system. Failure to follow the directions in this manual

and component literature could result in severe personal injury, death or substantial property

damage.

VERIFY PROPER OPERATION AFTER SERVICING

Service technician

(see following pages for instructions)

Owner maintenance

(see CGt User’s Information Manual for instructions)

nnu

Inspect:

• Reported problems

• Boiler area

• Air openings

• Flue gas vent system (and air piping)

• Pilot and main burner flames

• Water piping

• Boiler heating surfaces

• Burners, base and inlet air box

• Condensate drain system

Service:

• Inducer motor

• Oiled-bearing circulator

Start-up:

• Perform start-up per manual

Check/test:

• Gas piping

• Cold fill and operating pressures

• Air vents and air elimination

• Limit controls and cutoffs

• Expansion tank

• Boiler relief valve

Review:

• Review with owner

Daily

•  Check boiler area
•  Check air openings
•  Check boiler pressure
temperature gauge

Monthly

•  Check boiler interior piping
•  Check venting system
•  Check air vents
•  Check boiler relief valve
•  Check condensate drain system
•  Check automatic air vents (if
used)

Periodically

• Test low water cutoff (if used)

Every 6 months

• Oil inducer motor
• Operate relief valve

End of season

• Shut down procedure

Part Number

550-110-290/0219

CGt

GAS-FIRED WATER BOILER — Series 2 —

Boiler Manual

Service and maintenance — schedule

11a

Содержание CGt 2 Series





































































Результаты поиска

Содержание CGt 2 Series

Отзывы:

Похожие инструкции для CGt 2 Series

Бренды по названию

Популярные бренды

Weil-McLain CGt 2 Series, Руководство пользователя

Результаты поиска

Содержание CGt 2 Series

Отзывы:

Похожие инструкции для CGt 2 Series

Бренды по названию

Популярные бренды