Weil-McLain Aqua Balance WMB-120, Руководство пользователя, Страница: 99 / 132

Part number 550-100-305/0118
99
AquaBalance TM
W
ALL
M
OUNT GAS
-
FIRED WATER BOILER
—
Boiler Manual
Table 5
AquaBalance
™
list of System parameters (default settings)
System Parameters list (default settings)
There are 4 basic configurations within the DHW mode, selected by parameter DHW configuration (see Parameters list, Num.
1). Default value is 1 and it represents configuration 1. By changing DHW configuration (see Parameters list, Num. 1), all the data
will be automatically set at default condition. Parameters that will be changed according to the DHW mode are numbered from 9
to 46 (see Parameters list). All the parameters can be accessed with a communication package running on the PC. Some param-
eters are available by the installer TSP mode on the MMI or by the OT Room unit.
Category E2 prom parameters Unit Range Def
Description Num. Address Description Low High Value
DHW boiler type 1 CL5 – 05C8 –“]{!`"^\] Num 1 4 3
System 2 ML – 80D0 \#^#^"^J`€$"! Num 0 1 0
End user setting 3 ML – 80E2 Summer / Winter selection Num 0 1 1
End user setting 4 ML – 80E3 Economy / Comfort selection Num 0 1 0
End user setting 5 CL5 – 0A9D CH set point limit - HIGH °F 68 194 190
End user setting 6 CL5 – 056D CH user set point °F 68 194 158
Exhaust protection 7 CL5 – 050B Maximum exhaust gases temperature °F 32 255 185
Firmware version 8 ML – 80E8 Firmware version Num 0 99 03
–“]{! 9,1 CL5 – 066E DHW P factor Num 0 255 15
–“]{! 10,1 CL5 – 0691 DHW I factor Num 0 255 240
–“]{! 11,1 ML – 80EB DHW FF factor Num 0 255 0
–“]{! 12,1 ML – 80EC Fan absolute DHW maximum speed Hz 0 220 200
–“]{! 13,1 ML – 80ED Fan absolute CH maximum speed Hz 0 220 200
–“]{! 14,1 ML – 80EE Fan absolute minimum speed Hz 0 165 40
–“]{! 15,1 CL5 – 2D89 Fan offset low level Hz 0 220 10
–“]{! 16,1 ML – 80F0 Ignition level % 0 100 60
–“]{! 17,1 ML – 80F1 DHW maximum output boost/limit level % 75 125 100
–“]{! 18,1 ML – 80F2 DHW maximum output boost/limit time Sec 0 120 60
–“]{! 19,1 ML – 80F3 –“‰XJ^XZ€š `]XJ{‹X °F 68 194 167
–“]{! 20,1 ML – 80F4 –“‰XJ^XZ€š `]X?J{‹X °F 68 194 163
–“]{! 21,1 ML – 80F5 DHW over-temp_burnerOFF – setpoint °F 0 200 9
–“]{! 22,1 ML – 80F6 DHW over-temp_burnerON – setpoint °F 0 200 0
–“]{! 23,1 ML – 80F7 DHW over-temp_burnerOFF – solar °F 0 200 18
–“]{! 24,1 ML – 80F8 DHW over-temp_burnerON – solar °F 0 200 18
–“]{! 25,1 ML – 80F9 DHW start waiting time – solar1 Sec 0 255 5
–“]{! 26,1 ML – 80FA DHW start waiting time – solar2 Sec 0 255 10
–“]{! 27,1 ML – 80FB DHW start waiting time – solar3 Sec 0 255 20
–“]{! 28,1 CL5 – 0A5E DHW comfort switch on point °F 0 176 104
–“]{! 29,1 CL5 – 0A62 DHW comfort on time Sec 0 104 15
–“]{! 30,1 ML – 80FE DHW comfort off time1 Min 0 255 20
–“]{! 31,1 ML – 80FF DHW comfort off time2 Min 0 255 42
–“]{! 32,1 CL5 – 05A1 DHW OFF time Sec 30 255 120
–“]{! 33,1 CL5 - 0A04 DHW pump over-run time Sec 0 255 3
–“]{! 34,1 CL5 – 0A6D Delta T1 °F 0 108 32
–“]{! 35,1 CL5 – 0A92 Delta T2 °F 0 255 63
Figure 127 Troubleshooting suggestions for
AquaBalance
™
boilers — Fault displays and diagnostics
(continued)
34 Troubleshooting
(continued)