Weidmuller IE-WL-BL-AP-CL Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 76

background image

Wi-Fi device IE-WL-BL-AP-CL

Web Console Configuration

3-34

Beacon interval (for AP/Master mode only)

Setting

Description

Factory Default

Beacon Interval
(40 to 1000 ms)

Indicates the frequency interval of the beacon

100 (ms)

Inactive timeout (for AP mode only)

Setting

Description

Factory Default

1 to 240 seconds

Specifies how long before access point starts sending out client
alive packets

60 seconds

DTIM interval (for AP/Master mode only)

Setting

Description

Factory Default

Data Beacon Rate
(1 to 15)

Indicates how often the IE-WL-BL-AP-CL sends out a Delivery
Traffic Indication Message

1

Fragmentation threshold

Setting

Description

Factory Default

Fragment Length
(256 to 2346)

Specifies the maximum size a data packet before splitting and
creating another new packet

2346

RTS threshold

Setting

Description

Factory Default

RTS/CTS Threshold
(256 to 2346)

Determines how large a packet can be before the access point
coordinates transmission and reception to ensure efficient
communication

2346

NOTE

You can refer to the related glossaries in Appendix A for detailed information about the above-mentioned
settings. By setting these parameters properly, you can better tune the performance of your wireless network.

Antenna

Setting

Description

Factory Default

A/B/Both

Specifies the output antenna port. Setting “Antenna” to “Both”

allows 2x2 MIMO communication under 802.11n and 2T2R*
communication in legacy 802.11a/b/g modes.

Both

*Note: 2T2R is different from 802.11n’s multiple spatial data stream (2x2 MIMO), which doubles the

throughput. 2T2R transmits/receives the same piece of data on both the antenna ports.

WMM

Setting

Description

Factory Default

Enable/Disable

WMM is a QoS standard for WLAN traffic. Voice and video data
will be given priority bandwidth when enabled with WMM
supported wireless clients.
Note: WMM will always be enabled under 802.11n mode.

Enable

Turbo Roaming (for Client mode only)

Setting

Description

Factory Default

Enable/ Disable

Weidmüller

’s Turbo Roaming can enable rapid handover when

the IE-WL-BL-AP-CL, as a client, roams among a group of APs.

Disable

When Turbo Roaming is enabled, the following parameters will be shown:

•

Roaming threshold:

Determines when to start looking for new AP candidates. If the current connection

quality (SNR or Signal Strength) is lower than the specified threshold, the IE-WL-BL-AP-CL will start
background scanning and look for next-hop candidates.

«
...
32
33
34
35
36
...
»

Содержание IE-WL-BL-AP-CL













































































Отзывы:

Нет отзывов

Похожие инструкции для IE-WL-BL-AP-CL

Бренд: Ruckus Wireless Страницы: 3

Бренд: Sercomm Страницы: 76

WNR3500 - RangeMax Next Wireless-N Gigabit Router Wireless

Бренд: NETGEAR Страницы: 124

Бренд: Skyrc Страницы: 2

Бренд: Zte Страницы: 29

Бренд: SUNDRAY Страницы: 20

Бренд: Cuppon Страницы: 2

Бренд: Nortel Страницы: 130

Бренд: AAxeon Страницы: 50

Бренд: HEOS Страницы: 12

Бренд: H3C Страницы: 3

Бренд: H3C Страницы: 20

Бренд: Xirrus Страницы: 8

Бренд: Ebyte Страницы: 26

Barricade SMC7904WBRA

Бренд: SMC Networks Страницы: 2

Barricade SMCBR14UP

Бренд: SMC Networks Страницы: 77

ULTRA MINI BLUETOOTH

Бренд: Targus Страницы: 130

Бренд: Yealink Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды