Weidmuller IE-WL-BL-AP-CL Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 76

background image

Wi-Fi device IE-WL-BL-AP-CL

Supporting Information

B-75

About This User

’

s Manual

This manual is mainly designed for, but not limited to, the following hardware and firmware for the
IE-WL-BL-AP-CL:

•

Hardware Rev:

2.1.0

•

Firmware Ver:

1.16.16

You are strongly recommended to visit

Weidmüller’

s website (http://

www.Weidmueller.com/Downloads

) and

find the latest product datasheet, firmware, HIG (Hardware Installation Guide), User

’

s Manual and related

information.

NOTE

You can find out the hardware revision number of IE-WL-BL-AP-CL on the side label of the device.

The firmware version number can be seen on the

Overview

page, as follow:

DoC (Declaration of Conformity)

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

To assure continued compliance, (example

–

use only shielded interface cables when connecting

to computer or peripheral devices). Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not

be co-located or operated in conjunction with any other antenna or transmitter.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your
body.

«
...
73
74
75
76
»

Содержание IE-WL-BL-AP-CL













































































Отзывы:

Нет отзывов

Похожие инструкции для IE-WL-BL-AP-CL

Бренд: OBERON Страницы: 5

Бренд: Hamlet Страницы: 77

Бренд: Pakedge Страницы: 7

Бренд: Pakedge Страницы: 4

Бренд: BEC Страницы: 18

Edge Pro ERPro-8

Бренд: Ubiquiti Страницы: 20

Бренд: EnGenius Страницы: 2

NORA-W30 Series

Бренд: u-blox Страницы: 52

Бренд: Firetide Страницы: 32

Бренд: Pakedge Страницы: 10

B-Link B-LINK-MIFI

Бренд: Brickhouse Security Страницы: 8

WI DRIVE WID11GEN

Бренд: Dension Страницы: 26

Бренд: Linksys Страницы: 30

Бренд: Linksys Страницы: 31

Бренд: Linksys Страницы: 135

Бренд: T-Mobile Страницы: 4

Бренд: T-Mobile Страницы: 13

Бренд: T-Mobile Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды