manualshive.com logo in svg

Wegener UNITY500, Руководство пользователя

Поделиться
Скачать
Wegener UNITY500 Скачать руководство пользователя страница 23

UNITY 500

Page 23

Page 23 of 56

800001-01

The following definitions apply to Table 5:

•

 

Blink

 -

LED is OFF for 1 second, then blinks ON for 250 ms and OFF for 250 ms

between 1 and 12 times, according to the Alarm/Warning Code. Is then OFF for 1 second,
and blinks 1-12 times again.  This pattern continues until the alarm/warning condition is
cleared.  (For example, if the unit is displaying a “header search mode” alarm, the LED will
be OFF for 1 sec., then will blink (RED) ON for 250 ms and OFF for 250 ms five times.  It
will then be OFF for 1 sec, followed by blinking 5 times, etc.  The LED blinking RED
indicates an alarm, while AMBER indicates a warning.

•

 

Flash - 

ON for 100 ms, OFF for 100 ms.

•

 

Flutter

 - ON for 50 ms, OFF for 50 ms.

•

 

AMBER

 - RED and GREEN turned ON at the same time.

Note:

ms = 1/1000 second.

The conditions are listed in the order of their display priority with highest priority at the top.

Note that the alarm conditions are those conditions preventing the delivery of video.

2.4 

POWER-ON PROCEDURE

Apply power to the IRD.  The unit initializes various devices and configures itself according to
the EEPROM settings.  It then waits for the receiver section to complete its power up test, which
takes about 10 seconds.  When the receiver section passes its test, the IRD sends a tune
command and the Welcome Banner (example shown below) to the serial port.  If the unit is in
Terminal Mode, the banner displays on the terminal screen. The IRD then enters alarm mode
until all of the alarm conditions are cleared.

Your banner may be different from this example depending on options purchased.  Note that the
“Type H…”  text at the bottom of the screen is shown only if the serial device is set to Terminal
mode.

Figure 4. Welcome Banner

Wegener Communications Copyright 2000

Unity 500 Integrated Receiver Decoder

Application 

:  V106

Boot

:  V102

Xilinx

:  CA600048-01  100

Secure

:  600041  1.1

Tuner

:  L64724D

Type H for a list of terminal commands

Содержание UNITY500

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды