Weco UNIVERSAL 5K3HV Скачать руководство пользователя страница 6

Страница: 6 / 82

WECO 5K3 LV/HV

Statement:

The information and guidance contained in this manual is related to the

5K3 LV/HV

Stackable model of

battery. This manual contains two sections:

Section 2 is for LOW VOLTAGE APPLICATION

Section 3 is for HIGH VOLTAGE APPLICATION

In case of product upgrades or other reasons, this document will be adjusted accordingly. Unless otherwise

agreed, this document is intended to be used only as a guide, and all statements, information and advice in the

documentation shall not constitute any express or implied action in contradiction to local regulations or

standards.

For more information, please contact us.

The official information and the latest datasheet are available on

www.wecobatteries.com

It is essential that the Battery Module is equipped with the latest firmware version available.

New batteries always ship with the latest version of firmware.

From time to time, firmware will be updated to improve the functionalities and battery capabilities. The

latest version of the firmware is always available free of charge and can be updated by your local installer. You

can always contact

[email protected]

for additional information on the upgrade procedure.

Preface:

Thank you for choosing our product. We will provide you with a high-quality product as well as reliable

after-sale service. To protect against harm to both personnel and the product, please read this manual

carefully.

This manual provides detailed information on operation, maintenance and troubleshooting of the product as

well as health and safety advice.

Declaration:

The manufacturer holds the right of final explanation of any content in this manual.

All trademarks shown in this manual belong to their legitimate owners; trademarks of third parties,

product names, trade names, corporate names and companies mentioned may be trademarks owned by

their respective owners or registered trademarks of other companies and are used purely for explanatory

purposes and for the benefit of the owner, without any purpose of violation of the copyright in force.

NOTICE:

This Battery Module is designed to be used indoors.

The STANDARD IP21 degree of protection does not allow installation in outdoor environments even if sheltered
from the weather.

The Battery Modules must be stored indoors in a clean, dry, cool location in a limited access area.

Содержание UNIVERSAL 5K3HV



















































































Результаты поиска

Содержание UNIVERSAL 5K3HV

Отзывы:

Похожие инструкции для UNIVERSAL 5K3HV

Бренды по названию

Популярные бренды

Weco UNIVERSAL 5K3HV, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UNIVERSAL 5K3HV

Отзывы:

Похожие инструкции для UNIVERSAL 5K3HV

Бренды по названию

Популярные бренды