MAINTENANCE –
VERNIER TRIGGER ADJUSTMENTS
42
42
VERNIER TRIGGER ADJUSTMENTS
ANGEL™ 4
VERNIER TRIGGER ADJUSTMENTS
The trigger return stroke, over-travel and toe adjustments should be carried out in the
order shown and will enable the user to have total adjustment on the tactile feel and
trigger movement.
· Using a suitable Allen key undo the trigger adjustment locking screws
located
between the thumb wheels on both sides of the ANGEL™ by rotating counter
clockwise.
· Remove the grip cheek retaining screws and expose the circuit board
· Using a suitable Allen key back off the toe adjustment screw
by rotating
counter clockwise, now the trigger return stroke and over travel may be set.
· The vernier thumb wheel located at the top of the grip frame closest to the rear of
the ANGEL™
controls the over-travel.
· By viewing the ANGEL™ on the left hand side of the body rotate the thumb wheel
closest to the rear of the ANGEL™ slowly towards the rear of the ANGEL™ each click
at a time, this will reduces the over travel each click will be an incremental
reduction in the stroke.
· The vernier thumb wheel located at the top of the grip frame furthest to the rear of
the ANGEL™
controls the return stroke.
· By viewing the ANGEL™ on the left hand side of the body rotate the thumb wheel
furthest from the rear of the ANGEL™ slowly towards the rear of the ANGEL™ each
click at a time, this will reduces the return stroke, each click will be an incremental
reduction in the stroke.
· Further fine tuning can be achieved by adjusting the toe adjuster screw
.
Clockwise will cause the trigger to activate with less trigger movement counter
clockwise will result in a longer trigger stroke within the limits set by vernier
thumb wheels.
· Verify the trigger is functioning correctly.
· Replace grip cheek cover screws using a suitable metric Allen key.
· Very gently tighten the vernier thumb wheel locking screws
IMPORTANT NOTES: For re-assembly of components
· There must be sufficient over travel to activate the OPTO board, otherwise the
Opto-Trigger will not operate correctly.
· There must be sufficient return stroke to reset the OPTO board otherwise the
Opto-Trigger will not operate correctly.
· Should the trigger be incorrectly adjusted, re-adjust the return stroke by
repeating the procedures listed above or re-adjust the over travel by repeating
the procedures listed above.
· When adjusting the trigger stroke we recommend you apply a small amount of
Loctite™ low strength thread lock to the toe adjuster screw to prevent movement
due to vibration prior to adjustment.
· The vernier locking screw must not be over tightened otherwise damage may
occur to the vernier retention springs.
· The OPTO board is a non-mechanical switch that is silent in its operation and no
audible click is present.
· The OPTO board should not be exposed to direct sunlight or external strong
sources of light without the grip cheek fitted as this light will induce a safety
feature, that will prevents the ANGEL™ from firing whilst it remains exposed to
the external strong light.
· Never adjust the trigger stroke so that the trigger has so fine a movement that
accidental discharges may occur or that trigger bounce may occur leading to
accidental discharges.
1 2 3 4 5 6
8 9 10 11 12 1
7
1 2 3 4 5 6
8 9 10 11 12 1
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
• Ensure a barrel blocking device is fitted to the ANGEL™
• Ensure the hopper is removed from the ANGEL™
• Ensure that there are no paintballs in the ANGEL™
• Always remove the first stage regulator and relieve all residual gas pressure
from the ANGEL™ before disassembly.
• The ANGEL™ can hold a small residual charge of gas, typically 2 shots, with the
first stage regulator removed. Always discharge the marker in a safe direction to
relieve this residual gas pressure.
• Never adjust your trigger so fine that accidental discharge can occur due to
shock loads or vibration.
m
WARNING
ADHERE STRICTLY TO THESE
AND ALL OTHER SAFETY
INSTRUCTIONS AND GUIDELINES
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
1 2 3 4 5 6
8 9 10 11 12 13
7
