Wayne-Dalton TORQUEMASTER 5140 Скачать руководство пользователя | Manualshive

Страница: 37 / 38

background image

37

Please Do Not Return This Product To The Store.

Contact your local Wayne-Dalton dealer.

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at

www.wayne-dalton.com

MAINTENANCE

Painting

after surface has been properly prepared, it must be allowed to dry thoroughly, and then coated immediately with premium quality
latex house paint. Follow paint label directions explicitly. Oil base or solvent base paints are not recommended. Please note that if
substrate is exposed and not properly primed, painting with latex paint may cause accelerated rusting of the steel in the exposed area.

NOTES:
1.

Repainting of finish painted steel doors cannot be warranted, as this condition is totally beyond the door manufacturer’s control.

2.

Consult a professional coatings contractor if in doubt about any of the above directions.

3.

Follow directions explicitly on the paint container labels for proper applications of coatings and disposal of containers. Pay particular

attention to acceptable weather and temperature conditions in which to paint.

Painting Continued....

«
...
35
36
37
38
»

Содержание TORQUEMASTER 5140







































Отзывы:

Нет отзывов

Похожие инструкции для TORQUEMASTER 5140

Бренд: FAAC Страницы: 31

Бренд: 4Ddoors Страницы: 3

Бренд: 4Ddoors Страницы: 36

Бренд: WALKY Страницы: 12

Бренд: CAME Страницы: 64

Бренд: fadini Страницы: 13

Power Drive Security+ PD210CS

Бренд: Chamberlain Страницы: 80

Бренд: Itouchless Страницы: 11

Бренд: CAME Страницы: 144

Бренд: FAAC Страницы: 19

Бренд: FAAC Страницы: 19

Бренд: Polaris Страницы: 187

Бренд: Dea Страницы: 19

Бренд: Dea Страницы: 20

Бренд: Dea Страницы: 26

Бренд: Dea Страницы: 39

Бренд: Dea Страницы: 40

Бренд: FAAC Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды