Wayne-Dalton TORQUEMASTER 5140 Скачать руководство пользователя

Страница: 3 / 38

Please Do Not Return This Product To The Store.

Contact your local Wayne-Dalton dealer.

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at

www.wayne-dalton.com

Package Contents

(1)TORquEMasTER

sPRING TuBE

DOOR sECTIONs (as REquIRED)

(2) TOP BRaCkET slIDEs

1/4”-14 x 5/8” sElF TaPPING

sCREWs (as REquIRED)

1/4”-20 x 11/16” sElF DRIllING

sCREWs (as REquIRED)

(4) 1/4”-20 x 5/8”

CaRRIaGE BOlTs

(2) #12 x 1/2” PhIllIPs

hEaD sCREWs

(2) VERTICal

TRaCks Rh/lh

(2) 3/8”-16 x 3/4”

TRuss hEaD BOlTs

(1) CENTER BRaCkET

assEMBly

(2) quICk INsTall Rh/lh

FlaGaNGlE (as REquIRED)

(2) hORIzONTal TRaCks Rh/lh

NOTE:

DEPENDING ON ThE DOOR MODEl, sOME PaRTs lIsTED WIll NOT BE suPPlIED IF NOT

NECEssaRy. REaR suPPORTs May OR May NOT BE INCluDED WITh yOuR DOOR.

ROllERs

(as REquIRED)

COuNTER COVERs

(as REquIRED)

IDRIVE

OPERaTOR

(sOlD sEPaRaTEly)

(1) OPERaTOR BRaCkET

luBRICaTING OIl

(as REquIRED)

(2) hORIzONTal aNGlEs

(21-15/16” OR 80”)

(as REquIRED)

(2) TOP BRaCkET BasEs

Pull ROPE

(IF INCluDED)

COuNTER GEaRs

(as REquIRED)

5/16” x 1 5/8” hEx hEaD laG sCREWs

(as REquIRED)

(1) lOOsE WINDING shaFT

(sINGlE sPRING ONly)

3/8”- 16 x 3/4” hEx hEaD

BOlTs (IF INCluDED)

RIGhT aND lEFT CaBlE

DRuM assEMBlIEs

WEaThER sEals & NaIls

(IF INCluDED)

asyMMETRICal u-BaR

(IF INCluDED)

RIGhT & lEFT

DRuM WRaPs

TorqueMaster

- Single and Double Spring

Installation Instructions and Owner’s Manual

9100, 9600, 5120, 5140

IMPORTANT NOTICE!

Read these instructions carefully before
attempting installation. If in question about
any of the procedures, do not perform the
work. Instead, have a qualifi ed door agency
do the installation or repairs.

Part No. 302868

Rev. 2 08/04/2005

MaNual

1/4”- 20 FlaNGED hEx

NuTs (as REquIRED)

RIGhT & lEFT

END BRaCkETs

u-BaR

(IF INCluDED)

q.I. jaMB BRaCkETs

(as REquIRED)

(2) 3/8”- 16 hEx NuTs

36 TOOTh WORM GEaR

(as REquIRED)

(2) #10 PhIllIPs

hEaD sCREWs

(1) COTTER PIN

(1) 5/16” x 1-1/4”

ClEVIs PIN

Содержание TORQUEMASTER 5140







































Результаты поиска

Содержание TORQUEMASTER 5140

Отзывы:

Похожие инструкции для TORQUEMASTER 5140

Бренды по названию

Популярные бренды

Wayne-Dalton TORQUEMASTER 5140, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание TORQUEMASTER 5140

Отзывы:

Похожие инструкции для TORQUEMASTER 5140

Бренды по названию

Популярные бренды