Wayne-Dalton TORQUEMASTER 5140 Скачать руководство пользователя

Страница: 20 / 38

Tools Needed:

Please Do Not Return This Product To The Store.

Contact your local Wayne-Dalton dealer.

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at

www.wayne-dalton.com

drive

Installation

NOTE:

see

drive

main installation and

owners manual for

drive

parts.

IMPORTANT:

RIGhT aND lEFT haND

Is alWays DETERMINED FROM INsIDE
ThE GaRaGE lOOkING OuT.

lay the TorqueMaster

spring tube on

the floor (inside garage) in front of the
door with the labeled end to the left.

look into the opener’s left side to
ensure the left hand bearing and the
internal (black) sleeve are aligned with
the TorqueMaster

spring tube profile.

IMPORTANT:

hOlD OPENER By ThE

MaIN BODy. DO NOT hOlD By ThE
MOTOR.

NOTE:

Opener will not slide over the

TorqueMaster

spring tube label.

attempting to slide opener over the left
end of the TorqueMaster

spring tube

can damage the internal electronics.

Once aligned, slide the opener onto the
right hand end of the TorqueMaster

spring tube. as the right end of the
TorqueMaster

spring tube enters the

internal (black) sleeve, rotate the
opener back and forth slightly to help
aid alignment.

Continue sliding the opener onto the
TorqueMaster

spring tube. align the

right hand bearing with the
TorqueMaster

spring tube and slide

the opener completely onto the
TorqueMaster

spring tube until the

TorqueMaster

spring tube exits the

opener right hand bearing.

NOTE:

Do not force the opener onto the

TorqueMaster

spring tube if

misalignment occurs.

Continue sliding the opener to the
center of the TorqueMaster

spring

tube.

Plug the motor power cord into the
opener.

lEFT haND sIDE

TORquEMasTER

sPRING TuBE

aND BEaRING PROFIlEs alIGNED

RIGhT haND END

OF TORquEMasTER

sPRING TuBE

RIGhT haND sIDE

TORquEMasTER

sPRING TuBE aND

BEaRING PROFIlEs

alIGNED

PluG-IN MOTOR

POWER CORD

MOTOR

Tools Needed:

None

Содержание TORQUEMASTER 5140







































Результаты поиска

Содержание TORQUEMASTER 5140

Отзывы:

Похожие инструкции для TORQUEMASTER 5140

Бренды по названию

Популярные бренды

Wayne-Dalton TORQUEMASTER 5140, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание TORQUEMASTER 5140

Отзывы:

Похожие инструкции для TORQUEMASTER 5140

Бренды по названию

Популярные бренды