background image

38

Please Do Not Return This Product To The Store. 

Contact your local Wayne-Dalton dealer. 

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at 

www.wayne-dalton.com

limited warranty

Models 5120 And 5140

 

subject to the terms and conditions contained in this limited Warranty, Wayne-Dalton Corp. (“Manufacturer”) warrants the sections of the door, which is de-

scribed at the top of this page, for a period of 

TEN (10) yEARS

 from the date of installation against:

 

(i) 

The door becoming inoperable due to rust-through of the steel skin from the core of the door section, due to cracking, splitting, or other deterioration  

 

 

of the steel skin, or due to structural failure caused by separation or degradation of the foam insulation.

 

(ii) 

Peeling of the original paint on the door as a result of a defect in the original paint or in the application of the original paint coating, in cases where  

 

 

the door sections and the original paint:  (a) have not been subjected to adverse atmospheric conditions or contaminates (such as salt water  

 

 

 

or other marine environment, or to toxic or abrasive substances, including those in the air);  (b) have been maintained in compliance with  

 

 

 

Manufacturer’s recommendations; and  (c) have not been subject to physical abrasion, impacted by a hard object, or punctured (including  

 

 

 

without limitation “paint rub” occurring in metal to metal contact and movement).

 

The Manufacturer warrants the garage door hardware (except springs) and the tracks of the above-described door, for a period of 

TEN (10) yEARS

 from the date 

of installation, against defects in material and workmanship, subject to all the terms and conditions below.
 

The Manufacturer warrants those component parts of the door not covered by the preceding provisions of this limited Warranty against defects in material and 

workmanship for a period of 

ONE (1) yEAR

 from the date of installation.

 

The Manufacturer warrants the factory-applied finish and the factory attached stiles against fading and cosmetic changes from the time of installation for 

TwO 

(2) yEARS

. If the door is re-stained or re-painted, the TWO (2) yEaRs warranty for the factory-applied finish is void. The Model 5140 factory attached stiles (if applicable) are 

warranted against peeling, cracking, chalking, or delamination from the time of installation for 

TwO (2) yEARS

.

 

This limited Warranty is extended only to the person who purchased the product and continues to own the premises (where the door is installed) as his/her 

primary residence (“Buyer”).  This limited Warranty does not apply to residences other than primary, or to commercial or industrial installations, or to installations on rental 
property (even when used by a tenant as a residence). This limited Warranty is not transferable to any other person (even when the premises is sold), nor does it extend 
benefits to any other person.
 

The Manufacturer will not be responsible for any damage attributable to improper storage, improper installation, or any alteration of the door or its compo-

nents, abuse, damage from corrosive fumes or substances, salt spray or saltwater air, fire, acts of God, failure to properly maintain the door, or attempt to use the door, its 
components or related products for other than its intended purpose and its customary usage. This limited Warranty does not cover ordinary wear. This limited Warranty will 
be voided if the original finish is painted over, unless Manufacturer’s preparation and painting instructions are followed explicitly. This limited Warranty will be voided if any 
holes are drilled into the door, other than those specified by the Manufacturer.
 

ThIs lIMITED WaRRaNTy COVERs a CONsuMER PRODuCT as DEFINED By ThE MaGNusON-MOss aCT. NO WaRRaNTIEs, ExPREss OR IMPlIED (INCluDING 

BuT NOT lIMITED TO ThE WaRRaNTy OF MERChaNTaBIlITy OR FITNEss FOR a PaRTICulaR PuRPOsE) WIll ExTEND BEyOND ThE TIME PERIOD sET FORTh IN 

UNDER-

SCORED bOlD fACE TyPE

 IN ThIs lIMITED WaRRaNTy, aBOVE.

 

• 

Some States do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

 

any claim under this limited Warranty must be made in writing, within the applicable warranty period, to the dealer from which the product was purchased. un-

less the dealer is no longer in business, a written claim to the Manufacturer will be the same as if no claim had been made at all.
 

at the Manufacturer’s option, a service representative may inspect the product on site, or Buyer may be required to return the product to the Manufacturer at 

Buyer’s expense.  Buyer agrees to cooperate with any representative of the Manufacturer and to give such representative full access to the product with the claimed defect 
and full access to the location of its installation.
 

If the Manufacturer determines that the claim is valid under the terms of this limited Warranty, the Manufacturer will repair or replace the defective product.  

The decision about the manner in which the defect will be remedied will be at the discretion of the Manufacturer, subject to applicable law. ThE REMEDy WIll COVER ONly 
MaTERIal. ThIs lIMITED WaRRaNTy DOEs NOT COVER OThER ChaRGEs, suCh as FIElD sERVICE laBOR FOR REMOVal, INsTallaTION, PaINTING, shIPPING, ETC.
 

any repairs or replacements arranged by Manufacturer will be covered by (and subject to) the terms, conditions, limitations and exceptions of this limited 

Warranty; provided, however, that the installation date for the repaired or replaced product will be deemed to be the date the original product was installed, and this limited 
Warranty will expire at the same time as if there had been no defect. If a claim under this limited Warranty is resolved in a manner other than described in the immediately 
preceding paragraph, then neither this limited Warranty nor any other warranty from the Manufacturer will cover the repaired or replaced portion of the product.
 

ThE REMEDIEs FOR ThE BuyER DEsCRIBED IN ThIs lIMITED WaRRaNTy aRE ExClusIVE and take the place of any other remedy. The liability of the Manufactur-

er, whether in contract or tort, under warranty, product liability, or otherwise, will not go beyond the Manufacturer’s obligation to repair or replace, at its option, as described 
above. ThE MaNuFaCTuRER WIll NOT uNDER aNy CIRCuMsTaNCEs BE lIaBlE FOR sPECIal, INCIDENTal, OR CONsEquENTIal DaMaGEs, including (but not limited to) 
damage or loss of other property or equipment, personal injury, loss of profits or revenues, business or service interruptions, cost of capital , cost of purchase or replacement 
of other goods, or claims of third parties for any of the foregoing. 

 

• 

Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to   

 

 

you.

 

No employee, distributor, dealer, representative, or other person has the authority to modify any term or condition contained in this limited Warranty or to grant 

any other warranty on behalf of or binding on the Manufacturer, and anyone’s attempt to do so will be null and void.
 

Buyer should be prepared to verify the date of installation to the satisfaction of the Manufacturer.

 

The rights and obligations of the Manufacturer and Buyer under this limited Warranty will be governed by the laws of the state of Ohio, usa, to the extent per-

mitted by law.

 

• 

This Limited Warranty gives you specific legal rights and you may also have other rights, which may vary from State to State.

Thank you for your purchase

www.wayne-dalton.com

Covered by one or more of the following Patents; 5,408,724; 5,409,051; 5,419,010; 5,495,640; 5,522,446; 5,562,141; 5,566,740; 5,568,672; 5,718,533; 6,019,269; 
6,089,304; 6,644,378; 6,374,567; 6,561,256; 6,527,037; 6,640,872; 6,672,362; 6,725,898; 6,843,300; 6,915,573; 6,951,237; 7,014,386; 7,036,548; 7,059,380; 7,121,317; 
7,128,123; 7,134,471; 7,134,472; 7,219,392; 7,254,868. Canadian: 2,384,936; 2,477,445; 2,495,175; 2,507,590; 2,530,701; 2,530,74; 2, 2,532,824. Other US and foreign 
Patents pending

38

Please Do Not Return This Product To The Store. 

Contact your local Wayne-Dalton dealer. 

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at 

www.wayne-dalton.com

Содержание TORQUEMASTER 5140







































Отзывы: