Wayne-Dalton TORQUEMASTER 5140 Скачать руководство пользователя

Страница: 21 / 38

Tools Needed:

Please Do Not Return This Product To The Store.

Contact your local Wayne-Dalton dealer.

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at

www.wayne-dalton.com

INST

All

ATION

TORquEMasTER

sPRING TuBE

lOOsE

WINDING

shaFT

left hand Side

Single Spring Application

GROOVE

TORquEMasTER

sPRING TuBE

shake the TorqueMaster

spring tube

gently to extend the winding shafts out
about 5" on each side. For single
spring applications, there will be no left
hand spring in the TorqueMaster

spring tube.

lift the TorqueMaster

spring tube and

rest it on the top of the flagangles.
Orient TorqueMaster

spring tube so

that back of opener is flat against
header/mounting surface.

NOTE:

Cable drums are marked right

and left hand. Cable drums and
TorqueMaster

spring tube are cam

shaped to fit together only one way.

To install the cable drum, slide the
correct cable drum over the winding
shaft until the cable drum seats against
the TorqueMaster

spring tube. The

winding shaft must extend past the
cable drum far enough to expose the
splines and the groove. align the
winding shaft groove with the round
notch in the flagangle.

for Double Spring Applications:

Repeat for opposite side.

for Single Spring Applications:

Insert

the loose winding shaft into the left
hand cable drum prior to sliding the
cable drum over the TorqueMaster

spring tube.

NOTE:

On single spring applications,

take care in handling the loose winding
shaft (left side) so that it does not slide
back into the TorqueMaster

spring

tube.

WINDING

shaFT

COuNTERBalaNCE

CaBlE

TORquEMasTER

sPRING TuBE

CaBlE

DRuM

ROuND

NOTCh

WINDING

shaFT

GROOVE

sPlINEs

GROOVE

FlaGaNGlE

ROuND

NOTCh

TORquEMasTER

sPRING TuBE

CaBlE

DRuM

ROuND

NOTCh

WINDING

shaFT

FlaGaNGlE

RIGhT haND

CaBlE DRuM

lEFT haND

CaBlE DRuM

Cable Drum Installation

None

Содержание TORQUEMASTER 5140







































Результаты поиска

Содержание TORQUEMASTER 5140

Отзывы:

Похожие инструкции для TORQUEMASTER 5140

Бренды по названию

Популярные бренды

Wayne-Dalton TORQUEMASTER 5140, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание TORQUEMASTER 5140

Отзывы:

Похожие инструкции для TORQUEMASTER 5140

Бренды по названию

Популярные бренды