Wavenet 5000 Скачать руководство пользователя

Страница: 69 / 98

Using the Session Manager

5000 Mobile Terminal Product Guide (5000-REV2.21)

Chapter 6-57

tel>Auto-connect: IP: 192.168.0.1 Nodes: Any

>tel param save

tel>Telnet parameters saved

To see the current list of Auto-Connects, use the following command:

>tel acon list

tel>Auto-connects are enabled
tel>1) Auto-connect: IP: 192.168.0.1 Nodes: Any

Auto-Connects can be added and deleted as the following example illustrates:

>tel acon add host 192.168.0.99

tel>Auto-connect: IP: 192.168.0.99 Nodes: Any

>tel acon list

tel>Auto-connects are enabled
tel>1) Auto-connect: IP: 192.168.0.1 Nodes: Any
tel>2) Auto-connect: IP: 192.168.0.99 Nodes: Any

>tel acon del 1

tel>Deleting 1)Auto-connect: IP: 192.168.0.1 Nodes: Any

>tel acon list

tel>Auto-connects are enabled
tel>1) Auto-connect: IP: 192.168.0.99 Nodes: Any

>tel param save

tel>Telnet parameters saved

Note that when deleting Auto-Connects the list is renumbered with remaining Auto-

Connects numbered from 1.

Remember to save your Auto-Connect list after you make changes!

Several other commands are related to the Auto-Connect facility. The first is

Local Prompt

control:

>tel loc

tel>Local prompts are currently enabled

>tel loc off

tel>Local prompts are currently disabled

>tel loc on

tel>Local prompts are currently enabled

If Local Prompts are turned off, the “

Telnet

>” prompt is never visible on the terminal display, even if

no successful Auto-Connect was made. This provides extra security by not providing any local Telnet
capability to the operator at all.

With Local Prompts disabled, the terminal will continue to cycle through the Auto-

Connect list until a successful Auto-Connect is made.

The terminal will not be allowed to access other host computers if the host computers in

the Auto-Connect list are not available. Local Prompts must be re-enabled to access
other host computers that are not contained in the Auto-Connect list.

Remember to save your Local Prompt configuration after you make changes!

Содержание 5000



































































































Результаты поиска

Содержание 5000

Отзывы:

Похожие инструкции для 5000

Бренды по названию

Популярные бренды

Wavenet 5000, Руководство по эксплуатации продукта

Результаты поиска

Содержание 5000

Отзывы:

Похожие инструкции для 5000

Бренды по названию

Популярные бренды